| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Bouquerel, Jeremie
École Nationale Supérieure de Chimie de Lille
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (19/19 displayed)
- 2023Compelling Evidence for the Role of Retained Austenite in the Formation of Low Cycle Fatigue Extrusions in a 9Ni Steel
- 2021Impact of a heat treatment on the microstructure and the low cycle fatigue properties of a 9Ni steel
- 2021Impact of a heat treatment on the microstructure and the low cycle fatigue properties of a 9Ni steel
- 2021Study of the effect of the heat treatment parameters on the pearlitic transformation of an eutectoid steel wire
- 2021Study of the effect of the heat treatment parameters on the pearlitic transformation of an eutectoid steel wire
- 2021Retained austenite-aided cyclic plasticity of the quenched 9Ni steelcitations
- 2021Experimental mesoscopic investigation of the local cyclic plasticity of a non-oriented electrical steelcitations
- 2020Stability of fatigue cracks at 350 °C in air and in liquid metal in T91 martensitic steelcitations
- 2020Relations between microstructure and hardness of plain carbon steels using eddy current technique
- 2019Investigation of the Microstructure and Properties of TRIP 800 Steel Subjected to Low-Cycle Fatiguescitations
- 2019Influence of steel cleanliness on drawability of fine filaments with high tensile strengthcitations
- 2018Advanced processing of EBSD data to distinguish the complex microstructure evolution of a Cu-Ni-Si alloy induced by fatiguecitations
- 2018Behaviour of short and long cracks in air and in liquid metal in T91 steelcitations
- 2018Behaviour of short and long cracks in air and in liquid metal in T91 steelcitations
- 2018Cyclic Strain Localization Assessment by Advanced Microscopies
- 2015The electron microanalyzer (EPMA): a powerful device for the microanalysis of filled polymeric materialscitations
- 2013Effect of the forming process on the microstructure of aluminium parts for collective transports
- 2011Effect of heat treatment on liquid sodium embrittlement of T91 martensitic steelcitations
- 2008SIMULATION OF THE STATIC MECHANICAL BEHAVIOUR OF TRIP STEELS BY MICRO-MECHANICAL MODELLING
Places of action
| Organizations | Location | People |
|---|
article
Influence of steel cleanliness on drawability of fine filaments with high tensile strength
Abstract
The aim of the current study is to clarify the influence of steel cleanliness on the fracture during wet wire drawing of high strength high carbon very fine filaments. Methodologies for inclusion identification and for inclusion count were developed. Ninety percent of the fractured filaments were associated with an inclusion which was SiO2, or SiO2-CaO or SiO2-MgO. The fracture of the wires resulted from debonding of the inclusion from the matrix. Inclusion density assessed from total oxygen content in the wire was successfully and reliably obtained. Inclusions exhibited a wide range of sizes but mostly around 6 μm. The inclusion density did not appear as the only parameter that affects the fracture occurrence. An important effect of size and of chemical composition of the inclusions was found. A critical size of inclusions for fracture was observed but it depends on the chemical composition of inclusions.