| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Talib, Norfazillah
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (13/13 displayed)
- 2021The performance of modified Jatropha-based nanofluid during turning processcitations
- 2021Experimental analysis of tribological performance of modified Jatropha oil enriched with nanoparticle additives for machining application
- 2020Tribological Analyses of Modified Jatropha Oil with hBN and Graphene Nanoparticles as An Alternative Lubricant for Machining Processcitations
- 2020Tribological Assessment of Modified Jatropha Oil with hBN and Graphene Nanoparticles as a New Preference for the Metalworking fluidcitations
- 2018Investigation on the Tribological Behaviour of Modified Jatropha Oil with Hexagonal Boron Nitride Particles as a Metalworking Fluid for Machining Processcitations
- 2017Tribological Evaluation on Various Formulation of Modified RBD Palm Olein as Sustainable Metalworking Fluids for Machining Processcitations
- 2017Performance evaluation of biodegradable metalworking fluids for machining process
- 2017Tribological evaluation of hexagonal boron nitride in modified jatropha oil as sustainable metalworking fluidcitations
- 2016The Effect of Tribology Behavior on Machining Performances When Using Bio-based Lubricant as a Sustainable Metalworking Fluidcitations
- 2015Performance Evaluation of Chemically Modified Crude Jatropha Oil as a Bio-based Metalworking Fluids for Machining Processcitations
- 2014The Performance of Modified Jatropha-Oil Based Trimethylolpropane (TMP) Ester on Tribology Characteristic for Sustainable Metalworking Fluids (MWFs)citations
- 2013Effect of Pouring Temperature on Microstructure Properties of Al-Si LM6 Alloy Sand Castingcitations
- 2011Experimental study of vortex flow induced by a vortex well in sand castingcitations
Places of action
| Organizations | Location | People |
|---|
article
Experimental study of vortex flow induced by a vortex well in sand casting
Abstract
Fluid flow phenomena are very closely related to the casting quality and surface finish of the cast part. In addition, the good quality of the casting product can be achieved by using an optimum gating system design. In this work, a vortex well, which is one of the important components of gating system design, is utilized in order to demonstrate its effectiveness in improving the mechanical and microstructure properties of the cast part. An X-ray radiography test was performed in order to investigate the porosity distribution in castings with different vortex well dimensions. The scatter of flexure strength results was quantified by Weibull statistics. Microstructure analysis was conducted by using a scanning electron microscope (SEM) to examine the microstructure of selected casting specimens produced from the vortex well design. By optimizing the vortex well design, porosity inside the casting was significantly reduced, while the mechanical strength and reliability of aluminum casting were further enhanced.