| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Marsi, Noraini
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2021Dynamic mechanical analysis and morphology of petroleum-based and bio-epoxy foams with wood fillercitations
- 2021Compressive strength, sound absorption coefficient (SAC) and water absorption analysis of HDPE plastic waste reinforced polystyrene and Portland cement for lightweight concrete (LWC)citations
- 2021Bending strength analysis of HDPE plastic reinforced wood waste and thermoplastic polymer to replace ceramic tile compositescitations
- 2021Characterization of foam materials based on HDPE plastic waste for automotive seat application
- 2021Develop Interlocking Concrete Block Pavement from Portland Cement, Polystyrene and Bottom Ash on Pedestrian Roadcitations
- 2020The Mechanical Performance of Tile Based on Plastic Waste (PW) Mixed Wood Waste (MWW)citations
- 2020The Mechanical Performance of Pipe Based on Fiberglass Reinforced with Plastic Waste (FRPW) Compositescitations
- 2020Utilization of Banana (Musa Paradisiaca) Peel As Bioplastic for Planting Bag Application
- 2019Graphene Composite Blueberries based Pencil Lead act as Superhydrophobic Coating on Plastic Surfaces for Solar Application
- 2019Endurance of Renewable Polymer Composite to UV Irradiation
- 2018Dynamic Mechanical Thermal Analysis of Wood Polymer Composite Endurance to Prolonged Ultra Violet Irradiation Exposurecitations
- 2016Ballistic Impact Response of Woven Hybrid Coir/Kevlar Laminated Compositescitations
- 20153C-SiC-on-Si based MEMS packaged capacitive pressure sensor operating up to 500 ºC and 5 MPacitations
- 2015The Mechanical Characterization of Bending Test for MEMS Capacitive Pressure Sensor Based 3C-SiC in High Temperaturecitations
- 2014Development of high temperature resistant of 500 °C employing silicon carbide (3C-SiC) based MEMS pressure sensorcitations
- 2013Biopolymer Doped with Titanium Dioxide Superhydrophobic Photocatalysis as Self-Clean Coating for Lightweight Compositecitations
Places of action
| Organizations | Location | People |
|---|
article
Ballistic Impact Response of Woven Hybrid Coir/Kevlar Laminated Composites
Abstract
The effects of different laminated hybrid composites stacking configuration subjected to ballistic impact were investigated. The hybrid composites consist of woven coir (C) and woven Kevlar (K) layers laminated together. The samples of woven coir were prepared using handloom device. The composites were produced by stacking the laminated woven coir and Kevlar alternately with the presence of the binder. The samples were tested under ballistic impact with different stacking configuration. The results obtained had successfully achieved the National Institute of Justice (NIJ) standard level IIA with energy absorption of 435.6 kJ and 412.2 kJ under the projectile speed of between 330 m/s and 321 m/s respectively. Samples that having Kevlar layer at the front face and woven coir layer as back face achieved partial penetration during projectile impact. This orientation is proven to have good impact energy absorption and able to stop projectile at the second panel of the composites.