| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Blunt, Liam
University of Huddersfield
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (23/23 displayed)
- 2024Trueness of vat-photopolymerization printing technology of interim fixed partial denture with different building orientationcitations
- 2022Reaction Sintering of Biocompatible Al2O3-hBN Ceramicscitations
- 2020Challenges in Inspecting Internal Features for SLM Additive Manufactured Build Artifactscitations
- 2020The Detection of Unfused Powder in EBM and SLM Additive Manufactured Componentscitations
- 2020Development of an Additive Manufactured Artifact to Characterize Unfused Powder Using Computed Tomographycitations
- 2020Quantification of additive manufacturing induced variations in the global and local performance characteristics of a complex multi-stage control valve trimcitations
- 2019Introduction of a Surface Characterization Parameter Sdrprime for Analysis of Re-entrant Featurescitations
- 2019Hot-melt extrusion process impact on polymer choice of glyburide solid dispersionscitations
- 2019The challenges in edge detection and porosity analysis for dissimilar materials additive manufactured components
- 2018Optimization of surface determination strategies to enhance detection of unfused powder in metal additive manufactured components
- 2018Development of an AM artefact to characterize unfused powder using computer tomography
- 2018Characterisation of powder-filled defects in additive manufactured surfaces using X-ray CT
- 2018An interlaboratory comparison of X-ray computed tomography measurement for texture and dimensional characterisation of additively manufactured partscitations
- 2017Areal surface texture data extraction from X-ray computed tomography reconstructions of metal additively manufactured partscitations
- 2017Results from an interlaboratory comparison of areal surface texture parameter extraction from X-ray computed tomography of additively manufactured parts
- 2017Method for characterizing defects/porosity in additive manufactured components using computer tomography
- 2016Method for Characterization of Material Loss from Modular Head-Stem Taper Surfaces of Hip Replacement Devicescitations
- 2015Implementation of wavelength scanning interferometry for R2R flexible PV barrier films
- 2014Defect Detection in Thin-film Photovoltaics; Towards Improved Efficiency and Longevitycitations
- 2014Development of the basis for in process metrology for roll to roll production of flexible photo voltaics
- 2014An interferometric auto-focusing method for on-line defect assessment on a roll-to-roll process using wavelength scanning interferometry
- 2009Comparison of Type F2 Software Measurement Standards for Surface Texture
- 2006The use of CMM techniques to assess the wear of total knee replacements
Places of action
| Organizations | Location | People |
|---|
article
Reaction Sintering of Biocompatible Al2O3-hBN Ceramics
Abstract
<p>Biocompatible Al2O3-hBN ceramic was sintered from AlN and B2O3 precursors by reaction hot pressing at 1750 °C and 30 MPa for 8 min. The ceramic was compared to nonreactive (NR) one sintered from Al2O3 and BN under the same sintering conditions. The NR ceramic possesses 9% porosity as opposed to only 2% porosity for the reaction sintered Al2O3-hBN. The reaction sintered ceramic has crack resistance in the region of 5.0 ± 0.1 MPa·m1/2, which is approximately 20% higher than previously reported pure Al2O3 or Al2O3-hBN sintered without reaction support. The higher amount of hBN in the developed Al2O3-hBN material (27 vol %) facilitates hardness lowering to the region of 6 GPa, which is closer to the bone hardness and makes the ceramic machinable. Reaction sintering of the Al2O3-hBN composite opens a new area of creation and formation of load-bearing Al2O3-hBN ceramic bioimplants. </p>