| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Jin, Kailong
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (5/5 displayed)
- 2022Enhanced Mechanical Properties of Uniaxially Stretched Polylactide/Poly(ethylene oxide)- b-Poly(butylene oxide) Blend Filmscitations
- 2021Porous Fibers Templated by Melt Blowing Cocontinuous Immiscible Polymer Blendscitations
- 2020Crazing mechanism and physical aging of poly(lactide) toughened with poly(ethylene oxide)-block-poly(butylene oxide) diblock copolymerscitations
- 2019Bimodal Nanofiber and Microfiber Nonwovens by Melt-Blowing Immiscible Ternary Polymer Blendscitations
- 2018Compatibilization of Isotactic Polypropylene (iPP) and High-Density Polyethylene (HDPE) with iPP-PE Multiblock Copolymerscitations
Places of action
| Organizations | Location | People |
|---|
article
Crazing mechanism and physical aging of poly(lactide) toughened with poly(ethylene oxide)-block-poly(butylene oxide) diblock copolymers
Abstract
<p>Sustainable polymers are important alternatives to plastics and elastomers derived from petroleum resources. Poly(lactide) (PLA), a commercially available sustainable plastic, is a well-known success story. However, PLA lacks ductility and toughness, limiting the number of potential uses. In this study, small amounts of a liquid poly(ethylene oxide)-block-poly(butylene oxide) (PEO-PBO) diblock copolymer additive were blended with PLA to enhance its toughness and ductility. The incorporated PEO-PBO diblock copolymers generated a macrophase-separated morphology with particle diameters of 0.2-0.9 μm, and nearly matched refractive indices of PLA and PEO-PBO led to retention of optical transparency. Addition of just 1.8 wt % PEO-PBO into PLA led to a 20-fold increase in toughness, measured as the area under the stress-strain data in tension without affecting the bulk elastic modulus of the plastic. The micromechanical deformation process of the PEO-PBO/PLA blend was investigated via in situ small angle X-ray scattering during tensile testing. The total volume of the crazed material was proportional to the total surface area of the dispersed PEO-PBO particles, and both quantities increased with increasing PEO-PBO loading. Increasing the PEO-PBO loading also resulted in (A) an increase in particle size, causing a decrease in the craze initiation stress, and (B) an increase in fibril spacing, indicating a lower craze propagation stress. Furthermore, craze development was found to be independent of aging time. As a result, the PEO-PBO/PLA blend was able to remain ductile and tough for up to 114 days, exhibiting a 10-fold increase in elongation at break and toughness compared to neat PLA, which becomes brittle in less than 2 days. These results demonstrate that designing additives that promote deformation by crazing is an effective way to overcome the aging-induced embrittlement of glassy polymers.</p>