| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Rebholz, C.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (7/7 displayed)
- 2010A study of the nanostructure and hardness of electron beam evaporated TiAlBN coatingscitations
- 2010Mechanical and high pressure tribological properties of nanocrystalline Ti(N,C) and amorphous C:H nanocomposite coatingscitations
- 2010Structure and mechanical properties of low temperature magnetron sputtered nanocrystalline (nc-)Ti(N,C)/amorphous diamond like carbon (a-C:H) coatingscitations
- 2009Simulation and experimental analysis of substrate overmolding
- 2007Hard and superhard TiAlBN coatings deposited by twin electron-beam evaporationcitations
- 2006Correlation of elastic modulus, hardness and density for sputtered TiAlBN thin filmscitations
- 2005Applied encapsulation methods in mechatronics
Places of action
| Organizations | Location | People |
|---|
article
A study of the nanostructure and hardness of electron beam evaporated TiAlBN coatings
Abstract
TiAlBN coatings have been deposited by electron beam (EB) evaporation from a single TiAlBN material source onto AISI 316 stainless steel substrates at a temperature of 450 °C and substrate bias of − 100 V. The stoichiometry and nanostructure have been studied by X-ray photoelectron spectroscopy, X-ray diffraction and transmission electron microscopy. The hardness and elastic modulus were determined by nanoindentation. Five coatings have been deposited, three from hot-pressed TiAlBN material and two from hot isostatically pressed (HIPped) material. The coatings deposited from the hot-pressed material exhibited a nanocomposite nc-(Ti,Al)N/a-BN/a-(Ti,Al)B2 structure, the relative phase fraction being consistent with that predicted by the equilibrium Ti–B–N phase diagram. Nanoindentation hardness values were in the range of 22 to 32 GPa. Using the HIPped material, coating (Ti,Al)B0.29N0.46 was found to have a phase composition of 72–79 mol.% nc-(Ti,Al)(N,B)1 − x+ 21–28 mol.% amorphous titanium boride and a hardness of 32 GPa. The second coating, (Ti,Al)B0.66N0.25, was X-ray amorphous with a nitride+boride multiphase composition and a hardness of 26 GPa. The nanostructure and structure–property relationships of all coatings are discussed in detail. Comparisons are made between the single-EB coatings deposited in this work and previously deposited twin-EB coatings. Twin-EB deposition gives rise to lower adatom mobilities, leading to (111) (Ti,Al)N preferential orientation, smaller grain sizes, less dense coatings and lower hardnesses.