| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gunputh, Urvashi Fowdar
University of Derby
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (13/13 displayed)
- 2024Comparing Bio-Ester and Mineral-Oil Emulsions on Tool Wear and Surface Integrity in Finish Turning a Ni-Based Superalloycitations
- 2024Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatiguecitations
- 2023Effect of Grain Structure on Machinability of LPBF Inconel 718: A Critical Reviewcitations
- 2023Effect of Powder Bed Fusion Laser Sintering on Dimensional Accuracy and Tensile Properties of Reused Polyamide 11citations
- 2021Selective laser melting of a high precision turbomachinery application in IN718 alloy
- 2021High strain rate effect on tensile ductility and fracture of AM fabricated Inconel 718 with voided microstructurescitations
- 2021High strain rate effect on tensile ductility and fracture of AM fabricated Inconel 718 with voided microstructurescitations
- 2021Analysis of machining performance of Inconel 718 printed by PBF-LM (powder bed fusion laser melting)
- 2020Effect of element wall thickness on the homogeneity and isotropy of hardness in SLM IN718 using nanoindentationcitations
- 2020Effect of powder bed fusion laser melting process parameters, build orientation and strut thickness on porosity, accuracy and tensile properties of an auxetic structure in IN718 alloycitations
- 2020A review of in-situ grown nanocomposite coatings for titanium alloy implantscitations
- 2018Antibacterial Properties of TiO2 Nanotubes coated with nano-ZnO and nano-Ag
- 2018Anodised TiO 2 nanotubes as a scaffold for antibacterial silver nanoparticles on titanium implants.citations
Places of action
| Organizations | Location | People |
|---|
article
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
Abstract
In this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ± 350, ±400 and ± 450 MPa. The XY and ZX45 printing orientations were found to significantly improve service life. Although similar strain response was found for each orientation when the same stress amplitude was applied, slightly different fracture mechanisms were identified during the post-mortem surface observations.