| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Liu, Ming
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (17/17 displayed)
- 2024High dielectric filler for all-solid-state lithium metal batterycitations
- 2023Discharge performance of a high temperature phase change material with low-cost wire meshcitations
- 2023Hydrophobized MFC as Reinforcing Additive in Industrial Silica/SBR Tire Tread Compoundcitations
- 2022Cage Molecules Stabilize Lead Halide Perovskite Thin Filmscitations
- 2021Chemical degradation in Thermally Cycled Stainless Steel 316 with High-Temperature Phase Change Materialcitations
- 2019Barely Porous Organic Cages for Hydrogen Isotope Separationcitations
- 2018Investigation into the behaviour of aluminium and steel under melt/freeze cyclic conditionscitations
- 2017A eutectic salt high temperature phase change material: Thermal stability and corrosion of SS316 with respect to thermal cyclingcitations
- 2016Stability and corrosion testing of a high temperature phase change material for CSP applicationscitations
- 2016Review on concentrating solar power plants and new developments in high temperature thermal energy storage technologiescitations
- 2015Atomic Layer Deposited Hybrid Organic-Inorganic Aluminates as Potential Low-k Dielectric Materialscitations
- 2010Electrochemical reactivity, surface composition and corrosion mechanisms of the complex metallic alloy Al 3 Mg 2citations
- 2010The influence of yttrium (Y) on the corrosion of Mg-Y binary alloyscitations
- 2009A preliminary quantitative XPS study of the surface films formed on pure magnesium and on magnesium-aluminium intermetallics by exposure to high-purity watercitations
- 2009A first quantitative XPS study of the surface films formed, by exposure to water, on Mg and on the Mg-Al intermetallics: Al 3 Mg 2 and Mg 17 Al 12citations
- 2009Calculated phase diagrams and the corrosion of die-cast Mg-Al alloyscitations
- 2008Calculated phase diagrams, iron tolerance limit, and corrosion of Mg-Al alloyscitations
Places of action
| Organizations | Location | People |
|---|
article
A eutectic salt high temperature phase change material: Thermal stability and corrosion of SS316 with respect to thermal cycling
Abstract
<b>Highlights</b>- Its thermo-physical properties did not vary significantly over 1000 thermal cycles.- Corrosion products were identified and the thickness of the products were measured.- The mass-loss corrosion rate on SS316 increases linearly up to 350 cycles.- The corrosion rate stabilizes at 70 mg/cm<sup>2</sup> after 350 cycles.<b>Abstract</b>Thermal energy storage (TES) is a critical component in a concentrated solar power (CSP) plant since it is able to provide dispatchability and increase the capacity factor of the plant. Recently the Brayton power cycle using supercritical carbon dioxide (s-CO<sub>2</sub>) has attracted considerable attention as it allows a higher thermal to electric power conversion efficiency compared to the conventional Rankine cycle using subcritical steam. However, no commercial TES has yet been developed for integration with a s-CO<sub>2</sub> based plant. One reason is the lack of a suitable storage material. This work explores the use of a eutectic NaCl-Na<sub>2</sub>CO<sub>3</sub> salt as a reliable high temperature phase change material (PCM). The PCM has been thermally cycled up to 1000 times. Its thermo-physical properties have been measured before and after it has been subjected to the thermal cycling and its corrosion behavior has been investigated. This eutectic salt shows good thermal stability without degradation after cycling 1000 times between 600 and 650 °C. The corrosion rate on stainless steel 316 (SS316) increases linearly up to 350 cycles, and thereafter it stabilizes at 70mg/cm<sup>2</sup>.