| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Weiß, Sabine
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (11/11 displayed)
- 2024Improvement of photocatalytic performance and sensitive ultraviolet photodetectors using AC-ZnO/ZC-Ag2O/AZ-CuO multilayers nanocomposite prepared by spin coating method
- 2024Investigating the effect of Zr content on electrochemical and tribological properties of newly developed near β-type Ti-alloys (Ti–25Nb-xZr) for biomedical applications ; Untersuchung der Auswirkung des Zr-Gehalts auf die elektrochemischen und tribologischen Eigenschaften neu entwickelter β-naher Ti-Legierungen (Ti-25Nb-xZr) für biomedizinische Anwendungencitations
- 2023Nitriding effect on the tribological performance of CrN-, AlTiN-, and CrN/AlTiN-Coated DIN 1.2367 hot work tool steel ; Auswirkung des Nitrierens auf das tribologische Verhalten von CrN-, AlTiN- und CrN/AlTiN-beschichteten DIN 1.2367 Warmarbeitsstählencitations
- 2023Improvement of photocatalytic performance and sensitive ultraviolet photodetectors using AC-ZnO/ZC-Ag2O/AZ-CuO multilayers nanocomposite prepared by spin coating method ; Verbesserung der photokatalytischen Leistung empfindlicher Ultraviolett-Photodetektoren unter Verwendung von AC-ZnO/ZC-Ag2O/AZ-CuO-Multilayer-Nanokompositen abgeschieden durch Rotationsbeschichtungcitations
- 2023On the Heat Treatment of Selective-Laser-Melted 316Lcitations
- 2021Influence of Elemental Carbon (EC) Coating Covering nc-(Ti,Mo)C Particles on the Microstructure and Properties of Titanium Matrix Composites Prepared by Reactive Spark Plasma Sinteringcitations
- 2021Impact of Impulses on Microstructural Evolution and Mechanical Performance of Al-Mg-Si Alloy Joined by Impulse Friction Stir Weldingcitations
- 2020Hydrogen permeation, and mechanical and tribological behavior, of CrNx coatings deposited at various bias voltages on IN718 by direct current reactive sputtering
- 2019Enhanced structural and tribological performance of nanostructured Ti-15Nb alloy for biomedical applicationscitations
- 2018Hydrogen permeation, and mechanical and tribological behavior, of CrNx coatings deposited at various bias voltages on IN718 by direct current reactive sputteringcitations
- 2017Substrate Frequency Effects on Cr<SUB> x </SUB>N Coatings Deposited by DC Magnetron Sputteringcitations
Places of action
| Organizations | Location | People |
|---|
article
Enhanced structural and tribological performance of nanostructured Ti-15Nb alloy for biomedical applications
Abstract
Low modulus β-type Ti-15Nb alloys were prepared by subjecting them to different sintering temperatures (800, 900, 1000 and 1100 °C) and their morphological and structural properties were evaluated. X-ray diffraction analysis was used for the morphological characterization which indicated that the mean pore and crystallite size continuously decreased with increasing sintering temperature to reach the lowest values of 41 nm and 27.5 nm at 1100 °C, respectively. Moreover, the higher sintering temperature resulted in higher relative density, greater hardness and young's modulus of the Ti-15Nb alloys. Wear tests were conducted using a ball-on-plate type Oscillating tribometer, under different applied loads (2, 8 and 16 N) to evaluate their tribological characterization. The wear rate and friction coefficient were lower at higher sintering temperature. This enhancement in tribological properties was attributed to a grain refinement. The Ti-15Nb alloys sintered at 1100 °C showed the best tribological performance....