| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Price, Mark
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (15/15 displayed)
- 2015Predicting the crushing behaviour of composite material using high-fidelity finite element modellingcitations
- 2014Process efficiency in polymer extrusion: Correlation between the energy demand and melt thermal stabilitycitations
- 2014Energy monitoring and quality control of a single screw extrudercitations
- 2014Investigation of the process energy demand in polymer extrusion: a brief review and an experimental studycitations
- 2014Influence of Boundary Conditions on the Low Velocity Impact Damage Carbon Fibre Reinforced Plastic Plates (ICTWS2014-0501)
- 2014Low-cost Process monitoring for polymer extrusion
- 2013Integrating allowable design strains in composites with whole life valuecitations
- 2013Experimental investigation of thermoforming carbon fibre-reinforced polyphenylene sulphide compositescitations
- 2012Thermoforming carbon fibre-reinforced thermoplastic compositescitations
- 2012Digital Methods for Process Development in Manufacturing and Their Relevance to Value Driven Designcitations
- 2011The theoretical prediction of thermoformed carbon fibre reinforced thermoplastic materials in support of optimal process designcitations
- 2011Part form prediction methods for carbon fibre reinforced thermoplastic composite materials
- 2010Development of a digital methodology for composite process & manufacture in aerospace assembliescitations
- 2006Modified stiffened panel analysis methods for laser beam and friction stir welded aircraft panelscitations
- 2006The Characterization of Friction Stir Welding Process Effects on Stiffened Panel Buckling Performance
Places of action
| Organizations | Location | People |
|---|
article
Integrating allowable design strains in composites with whole life value
Abstract
Fibre-Reinforced Plastics (FRPs) have been used in civil aerospace vehicles for decades. The current state-of-the-art in airframe design and manufacture results in approximately half the airframe mass attributable to FRP materials. The continual increase in the use of FRP materials over metallic alloys is attributable to the material's superior specific strength and stiffness, fatigue performance and corrosion resistance. However, the full potential of these materials has yet to be exploited as analysis methods to predict physical failure with equal accuracy and robustness are not yet available. The result is a conservative approach to design, but one that can bring benefit via increased inspection intervals and reduced cost over the vehicle life. The challenge is that the methods used in practice are based on empirical tests and real relationships and drivers are difficult to see in this complex process and so the trade-off decision is challenging and uncertain. The aim of this feasibility study was to scope a viable process which could help develop some rules and relationships based on the fundamental mechanics of composite material and the economics of production and operation, which would enhance understanding of the role and impact of design allowables across the life of a composite structure.