| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Ahmad, H.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2023Effect of organic impurity in additive manufactured Ti-6Al-4Vcitations
- 2022Microstructural architecture and mechanical properties of empowered cellulose-based aerogel composites via TEMPO-free oxidationcitations
- 2022A high-precision extensometer system for ground displacement measurement using fiber Bragg gratingcitations
- 2022A Hi h-Precision Extensometer System for Ground Displacement Measurement Using Fiber Bragg Gratingcitations
- 2020Properties of C/C-SiC composites produced via transfer moulding and inner siliconizationcitations
- 2019New large-scale production method for C/C-SiC ceramics: Investigating the influence of chopped and nonwoven CFcitations
- 2019Influence of initial fibre length and content used in the injection moulding of CFRP on the properties of C/C and C/C-SiC compositescitations
- 2019Modification of the thermoset injection moulding process for shaping to increase the fibre length in C/C-SiC ceramics produced by the LSI processcitations
- 2017The Development of Lead-Free Sliding Contacts Based on Bronze-Graphite Composites through Powder Injection Mouldingcitations
- 2014Strength prediction of notched woven composite plates using a cohesive zone approachcitations
- 2011Double-pass erbium-doped zirconia fiber amplifier for wide-band and flat-gain operationscitations
- 2010Performance comparison of Zr-based and Bi-based erbium-doped fiber amplifierscitations
- 2010Wideband EDFA based in erbium doped crystalline zirconia yttria alumino silicate fibercitations
- 2005Direct UV writing for channel definition on FHD silica-on-silicon
Places of action
| Organizations | Location | People |
|---|
article
Double-pass erbium-doped zirconia fiber amplifier for wide-band and flat-gain operations
Abstract
The double-pass erbium-doped zirconia fiber amplifier (EDZFA) is proposed and demonstrated to provide a wide-band amplification as well as flat-gain operation in both the C- and L-band regions using only a single-gain medium.The proposed amplifier utilizes an erbium-doped zirconia fiber (EDZF) with erbium ion concentration of 2800 ppm as a gain medium. The medium is fabricated in a ternary glass host, zirconia-yttria-aluminium codoped silica fiber through solution doping technique along with modified chemical vapor deposition (MCVD). Compared to a single-pass operation, the double-pass EDZFA shows a better gain performance. At input signal power of 0 dBm and the optimum EDZF length of 2m, a flat gain of around 16dB is achieved by the proposed double-pass amplifier with gain variation of approximately 2.5dB throughout the wavelength range from 1530 to 1590nm. However, the noise figure of the double-pass amplifier is slightly higher than that of the single-pass due to inefficient population inversion at the input part of the amplifier.