| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Burtscher, Michael
Montanuniversität Leoben
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2024Micro-Mechanical Fracture Investigations on Grain Size Tailored Tungsten-Copper Nanocompositescitations
- 2024Mechanical processing and thermal stability of the equiatomic high entropy alloy TiVZrNbHf under vacuum and hydrogen pressurecitations
- 2023Effect of wire-arc directed energy deposition on the microstructural formation and age-hardening response of the Mg-9Al-1Zn (AZ91) alloycitations
- 2023Deformation and failure behavior of nanocrystalline WCucitations
- 2023Precipitation behavior of hexagonal carbides in a C containing intermetallic γ-TiAl based alloycitations
- 2023From unlikely pairings to functional nanocomposites: FeTi–Cu as a model systemcitations
- 2023On the stability of Ti(Mn,Al)2 C14 Laves phase in an intermetallic Ti–42Al–5Mn alloycitations
- 2023On the stability of Ti(Mn,Al)$_2$ C14 Laves phase in an intermetallic Ti–42Al–5Mn alloycitations
- 2022In situ micromechanical analysis of a nano-crystalline W-Cu compositecitations
- 2022Oxidation resistance of cathodic arc evaporated Cr$_{0.74}$Ta$_{0.26}$N coatingscitations
- 2021High-Temperature Nanoindentation of an Advanced Nano-Crystalline W/Cu Compositecitations
- 2020In situ fracture observations of distinct interface types within a fully lamellar intermetallic TiAl alloycitations
- 2020An Advanced TiAl Alloy for High-Performance Racing Applicationscitations
- 2019The creep behavior of a fully lamellar γ-TiAl based alloycitations
Places of action
| Organizations | Location | People |
|---|
article
Deformation and failure behavior of nanocrystalline WCu
Abstract
The technical potential of WCu alloys is limited by the modest fracture characteristics of the material system in its coarse-grained condition. To provide a nanocrystalline microstructure and improve mechanical properties, a W-50 at.% Cu composite was processed using high-pressure torsion deformation at a temperature of 200 ◦C. Therefore, two specimens were subjected to 100% and 1000% shear strains, respectively. Scanning electron and scanning transmission electron microscopy, including nanoscale energy dispersive X-ray spectroscopy mappings, were used to quantify the resulting microstructures. The average grain sizes for the 100% and 1000% deformed specimens were determined to be 14.7 ± 6.6 nm and 10.5 ± 5.6 nm, with the amount of mechanically intermixed W in the Cu grains increasing from 15.4 at.% to 15.9 at.%. X-ray diffraction and selected area electron diffraction studies both revealed strained lattice parameters of the W and Cu phases, respectively. Mechanical properties were investigated using in-situ notched microcantilever tests. The mean conditional fracture toughness and J-integral values were comparable for both conditions, at 3.7 ± 0.4 MPa√m and 245 ± 58 J/m2, respectively. The related behavior could be attributed to the low fault tolerance of the highly deformed states and was substantiated by cleaved globular W grains along the fractured surfaces. In addition, the detailed relationship between the altered grain boundary conditions, the degree of mechanical intermixing and the influence of the different microstructures on the fracture properties were carefully evaluated and discussed to pave the way for future application of these high-strength nanocomposites.