| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Molak, Rafał
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (11/11 displayed)
- 2021Influence of an aluminizing process on the microstructure and tensile strength of the nickel superalloy IN 718 produced by the Selective Laser Meltingcitations
- 2019Microstructure and corrosion resistance of warm sprayed titanium coatings with polymer sealing for corrosion protection of AZ91E magnesium alloycitations
- 2019Corrosion Resistance of Aluminum Coatings Deposited by Warm Spraying on AZ91E Magnesium Alloycitations
- 2019Functional properties of the novel hybrid coatings combined of the oxide and DLC layer as a protective coating for AZ91E magnesium alloycitations
- 2018The effect of microstructure anisotropy on low temperature fracture of ultrafine-grained ironcitations
- 2017Fatigue crack growth rate and tensile strength of Re modified Inconel 718 produced by means of selective laser meltingcitations
- 2016Influence of the corrosive environment on the Portevin–Le Chatelier plastic instability phenomenon in Al–1Mg and Al–3Mg model alloys
- 2016The effect of specimen size and Surface conditions on the local mechanical properties of 14MoV6 ferritic–pearlitic steelcitations
- 2014Magnesium AZ91 alloy cast mechanical properties measured by the Miniaturized Disc-Bend Testcitations
- 2012Strength and thickness of the layer of materials used for ceramic veneers bonding
- 2010Studies of Cu after severe plastic deformationcitations
Places of action
| Organizations | Location | People |
|---|
article
The effect of specimen size and Surface conditions on the local mechanical properties of 14MoV6 ferritic–pearlitic steel
Abstract
The paper describes multiscale experimental techniques required for determining the mechanical response of a ferritic–pearlitic steel (14MoV6). Accordingly, five different sets of specimens ranging from macro to micro size scales are utilized and whose experimental results have been compared. Digital image correlation is employed to measure deformations on the surface of the test specimens under tensile loading conditions. The influence of the surface conditions on the residual stress distribution was investigated by means of X-ray synchrotron diffraction. In addition, the effects of specimen size, surface conditions and the number of grains in the cross-section of the specimens on mechanical properties are examined. It is observed that key material parameters including the yield stress, tensile strength and elongation to failure are dependent on specimen size. In addition, the results demonstrate that the number of grains in the cross-section of the specimens significantly influence the material response during uniaxial tensile testing. On the other hand, the surface treatment of the micro tensile test specimens bring about reducing differences in mechanical properties between standard and miniature specimens.