693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Kratz, James
University of Bristol
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (46/46 displayed)
- 2024Effect of pre-curing on thermoplastic-thermoset interphasescitations
- 2024Microstructural analysis of unidirectional composites: a comparison of data reduction schemes
- 2024CFRP layer-by-layer curing using research-based automated deposition systemcitations
- 2024Effects of accelerated curing in thermoplastic particle interleaf epoxy laminatescitations
- 2024Annotator bias and its effect on deep learning segmentation of uncured composite micrographs
- 2024The effect of semi-curing on neat resin mode I fracture propertiescitations
- 2024Optimization and mechanical response of modular infusion compaction and normalization
- 2023A Feasibility Study for Additively Manufactured Composite Tooling
- 2023Effects of heat transfer coefficient variations on composite curingcitations
- 2023Automatic process control of an automated fibre placement machinecitations
- 2023Additively manufactured cure tools for composites manufacturecitations
- 2023In-situ defect detection and correction using real time automated fibre placement
- 2023The influence of key processing parameters on thermoset laminate curingcitations
- 2023The effect of convolutional neural network architectures on phase segmentation of composite material X-ray micrographscitations
- 2022Large Scale Forming of Non-Crimp Fabrics for Aerostructurescitations
- 2022Effects of heat transfer coefficient variations on composite curingcitations
- 2022The Effect of Process Parameters on First Ply Deposition in Automated Fibre Placementcitations
- 2022Tracking consolidation of out-of-autoclave prepreg corners using pressure sensorscitations
- 2022A FEASIBILITY STUDY OF ADDITIVELY MANUFACTURED COMPOSITE TOOLING
- 2021Modelling compaction behavior of toughened prepreg during automated fibre placement
- 2021Lab-based in-situ micro-CT observation of gaps in prepreg laminates during consolidation and curecitations
- 2020Predicting consolidation-induced wrinkles and their effects on composites structural performancecitations
- 2020Experimental characterisation of the in-plane shear behaviour of UD thermoset prepregs under processing conditionscitations
- 2019Modelling of the in-plane shear behavior of uncured thermoset prepreg
- 2019Heat transfer simulation of the cure of thermoplastic particle interleaf carbon fibre epoxy prepregscitations
- 2018Experimental Characterisation of In-plane Shear Behaviour of Uncured Thermoset Prepregs
- 2018Experimental and numerical investigation of full scale impact test on fibre-reinforced plastic sandwich structure for automotive crashworthiness
- 2018Out-of-Autoclave Prepreg Processingcitations
- 2017Improvement of the in-plane crushing response of CFRP sandwich panels by through-thickness reinforcementscitations
- 2017Resource-friendly carbon fiber compositescitations
- 2017An experimental technique to characterize interply void formation in unidirectional prepregscitations
- 2017Resource-friendly carbon fiber composites:combining production waste with virgin feedstockcitations
- 2017Void modelling and virtual testing of prepreg materials from 3D image capture
- 2017Tracking the evolution of a defect, characteristic of AFP layup, during cure with in-process micro-CT scanning
- 2016Predicting wrinkle formation in components manufactured from toughened UD prepreg
- 2016Reclaiming in-process composite waste for use in energy absorbing sandwich structures
- 2016Understanding and prediction of fibre waviness defect generation
- 2016Developing cure kinetics models for interleaf particle toughened epoxies
- 2016Visualising process induced variations in the manufacture of tufted sandwich panels
- 2015Towards the development of an instrumented test bed for tufting visualisation
- 2014Vacuum-bag-only prepreg processing of honeycomb structures
- 2014Vacuum-Bag Manufacturing of Honeycomb Structures
- 2014Vacuum-bag-only prepreg processing of honeycomb structures:From lab-scale experiments to an aircraft demonstrator
- 2013Thermal models for MTM45-1 and Cycom 5320 out-of-autoclave prepreg resinscitations
- 2013Anisotropic air permeability in out-of-autoclave prepregscitations
- 2010Out-of-autoclave honeycomb structures
Places of action
| Organizations | Location | People |
|---|
article
CFRP layer-by-layer curing using research-based automated deposition system
Abstract
Composite laminates of carbon fibres and a toughened snap-cure epoxy matrix were manufactured using a proof-of-concept layer-by-layer curing technique and compared to equivalent hot-press cured laminates. The layer-by-layer approach used a roller and a heated metal tool to deposit and cure a pre-preg layer to a degree-of-cure below gelation (α = 0.41) before applying the next layer, removing the need for a further curing step after deposition. The layer-by-layer process was found to produce laminates with evenly distributed micro-porosity (∼2.9 %), whereas press molded laminates at equivalent pressures featured higher porosity (∼4.7 %), that was concentrated in the inter-ply regions that were laminated together. Further work is needed to optimize the process variables for laminate quality, manage roller contamination, and study non-flat geometries.