| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Schulte, Karl
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (15/15 displayed)
- 2019Fracture, failure and compression behaviour of a 3D interconnected carbon aerogel (Aerographite) epoxy compositecitations
- 2018Fundamentals of the temperature-dependent electrical conductivity of a 3D carbon foam—Aerographite
- 2018Thermomechanical characteristics of ODF-silica Nafion® nanocomposite for PEMFCs application
- 20173D carbon networks and their polymer compositescitations
- 2017Compression fracture of CFRP laminates containing stress intensifications
- 2017Growth model of a carbon based 3D structure (Aerographite) and electrical/mechanical properties of composites
- 2016Fracture, failure and compression behaviour of a 3D interconnected carbon aerogel (Aerographite) epoxy compositecitations
- 2016Electro-mechanical piezoresistive properties of three dimensionally interconnected carbon aerogel (Aerographite)-epoxy compositescitations
- 2015Three-dimensional Aerographite-GaN hybrid networkscitations
- 2015Three-dimensional Aerographite-GaN hybrid networks: single step fabrication of porous and mechanically flexible materials for multifunctional applications
- 2013Improvement of carbon nanotube dispersion in thermoplastic composites using a three roll mill at elevated temperaturescitations
- 2011Characterization of the state of dispersion of carbon nanotubes in polymer nanocomposites
- 2009CFRP-recycling following a pyrolysis route : process optimization and potentials
- 2008Direction sensitive bending sensors based on multi-wall carbon nanotube/epoxy nanocompositescitations
- 2008Catalytically active CNT-polymer-membrane assembliescitations
Places of action
| Organizations | Location | People |
|---|
article
Catalytically active CNT-polymer-membrane assemblies
Abstract
<p>A new membrane electrode assembly set up for catalytic processes containing carbon nanotubes has been developed. The process includes the nanotube synthesis, sputter deposition of platinum as catalyst and the membrane casting. Aligned nanotube carpets were grown from toluene/ferrocene solutions and sputtered with platinum. Subsequently the assembly was investigated using cyclic voltammetry to confirm a sufficient catalyst activity. A procedure was developed to embed the carbon nanotubes doped with catalyst into SPEEK membranes, while preserving the aligned structure and keeping some surface area of the catalyst-doped nanotubes free of membrane material to allow for easy access to reactants. So far the best results were obtained using an aligned but somewhat loose nanotube structure and a deposition of 0.034 mg/cm<sup>2</sup> Pt, forming a combination of small catalyst clusters and a thin film. The assemblies are optimized in respect to application in fuel cells and functional membranes.</p>