| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Kruszewski, Mirosław
Warsaw University of Technology
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2024Microstructure and Corrosion of Mg-Based Composites Produced from Custom-Made Powders of AZ31 and Ti6Al4V via Pulse Plasma Sinteringcitations
- 2024A comparative study of oxidation behavior of Co4Sb12 and Co4Sb10.8Se0.6Te0.6 skutterudite thermoelectric materials fabricated via fast SHS-PPS routecitations
- 2023Rapid fabrication of Se-modified skutterudites obtained via self-propagating high-temperature synthesis and pulse plasma sintering routecitations
- 2023In-depth analysis of the influence of bio-silica filler (Didymosphenia geminata frustules) on the properties of Mg matrix compositescitations
- 2022Thermoelectric properties of bismuth-doped magnesium silicide obtained by the self-propagating high-temperature synthesiscitations
- 2022Heat Treatment of NiTi Alloys Fabricated Using Laser Powder Bed Fusion (LPBF) from Elementally Blended Powderscitations
- 2022Influence of Ag particle shape on mechanical and thermal properties of TIM jointscitations
- 2022A comparison of the microstructure-dependent corrosion of dual-structured Mg-Li alloys fabricated by powder consolidation methods: Laser powder bed fusion vs pulse plasma sinteringcitations
- 2022Pressureless Direct Bonding of Au Metallized Substrate with Si Chips by Micro-Ag Particlescitations
- 2021Microstructure and Thermoelectric Properties of Doped FeSi2 with Addition of B4C Nanoparticlescitations
- 2020Thermoelectric properties of Cu2S obtained by high temperature synthesis and sintered by IHP methodcitations
- 2019Microstructure and thermoelectric properties of p and n type doped β-FeSi2 fabricated by mechanical alloying and pulse plasma sinteringcitations
- 2018Skutterudite (CoSb3) thermoelectric nanomaterials fabricated by Pulse Plasma in Liquidcitations
- 2017Design of interfacial Cr 3 C 2 carbide layer via optimization of sintering parameters used to fabricate copper/diamond composites for thermal management applicationscitations
- 2014Thermal conductivity enhancement of copper–diamond composites by sintering with chromium additivecitations
- 2011W/steel joint fabrication using the pulse plasma sintering (PPS) methodcitations
Places of action
| Organizations | Location | People |
|---|
article
Microstructure and thermoelectric properties of p and n type doped β-FeSi2 fabricated by mechanical alloying and pulse plasma sintering
Abstract
N and p type doped, ß- FeSi2 was obtained by pulse plasma sintering (PPS) of mechanically alloyed Fe, Si with Mn, Co, Al, P as dopants. The consolidated samples were subsequently annealed at 1123 K for 36 ks. SEM observations proved that the samples consolidated by PPS preserve fine grain size of the mechanically alloyed ß-FeSi2 and the low porosity. The results of XRD measurements confirmed for all samples a nearly complete transformation from.- and .- into ß-FeSi2 phase after annealing. Their thermal conductivity decreases significantly with the increase of the test temperature in the entire rage of the temperatures of practical meaning. With the exception of the Mn-doped, all samples exhibited a high Seebeck coefficient, with its highest value for FeSi1.95P0.05 exceeding -400 µV/K up to 550 K. The Mn and Co –Fe site dopants revealed a stronger effect on the thermoelectric properties with 0.15 ZT parameter at 773 K for Fe0.97Co0.03Si2 alloy. The thermoelectric properties of PPS sintered samples were compared to the previously reported consolidated by hot pressing and spark plasma sintering. It has been concluded that the pulse plasma sintering offers an alternative to the already explored methods of production of thermoelectric materials.