| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Sivaswamy, Giribaskar
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (15/15 displayed)
- 2023Effect of heat treatments on microstructure and mechanical properties of low-cost Ti-6Al-4V alloy produced by thermo-mechanical powder consolidation routecitations
- 2023Miniaturised experimental simulation of open-die forgingcitations
- 2022An innovative constitutive material model for predicting high temperature flow behaviour of inconel 625 alloycitations
- 2022An analysis of the forgeability of Ti-10V-2Fe-3Al β titanium alloy using a combined Estrin Mecking and Avrami material constitutive modelcitations
- 2021A novel cyclic thermal treatment for enhanced globularisation kinetics in Ti-6Al-4V alloycitations
- 2021Effect of texture and mechanical anisotropy on flow behaviour in Ti-6Al-4V alloy under superplastic forming conditionscitations
- 2021A new route for developing ultrafine-grained Al alloy strips using repetitive bending under tensioncitations
- 2020Formability of AA-7075 sheets subjected to repetitive bending under tension
- 2020Mechanical response and microstructure evolution of commercially pure titanium subjected to repetitive bending under tensioncitations
- 2018Design and validation of a fixture for positive incremental sheet formingcitations
- 2018Effect of deformation-induced adiabatic heating on microstructure evolution during open-die screw press forging of Ti-6Al-4V.
- 2017Effect of incremental equal channel angular pressing (I-ECAP) on the microstructural characteristics and mechanical behaviour of commercially pure titaniumcitations
- 2017Microstructure and mechanical properties of Al-1050 during incremental ECAPcitations
- 2014Complex Incremental Sheet Forming Using Back Die Support on Aluminium 2024, 5083 and 7075 alloyscitations
- 2014Improvement in ductility in commercially pure titanium alloys by stress relaxation at room temperaturecitations
Places of action
| Organizations | Location | People |
|---|
article
A new route for developing ultrafine-grained Al alloy strips using repetitive bending under tension
Abstract
In this work, the mechanical behaviour and microstructure changes of AA-7075 alloy subjected to a repetitive-bending-under-tension (R-BUT) process were studied. In the R-BUT process, a metallic strip undergoes repeated localised bending and unbending. Load-displacement curves derived from R-BUT tested samples displayed a drastic increase in elongation to failure as compared to samples subjected to standard tensile tests. Additionally, the results confirmed that the force required to deform the R-BUT samples is much reduced as compared to the load required during simple tension. Finite element analysis confirmed that the sample subjected to the R-BUT process underwent intense shear deformation. Transmission-electron-microscopy (TEM) and electron-backscattered-diffraction (EBSD) analysis of the deformed matrix from the ND-RD plane (through-thickness) exhibited evidence for the formation of fine grains. TEM analysis confirmed that the fine grains formed were in the size range of 200-400 nm. Intense shear deformation experienced by the matrix led to shearing followed by spheroidization of precipitate particles. The influence of precipitate particles on the grain refinement process through Particle Stimulated Nucleation of fine grains in the matrix is also presented. EBSD analysis suggested that a Continuous Dynamic Recrystallisation process is the key mechanism behind the grain refinement in the sample during R-BUT processing.