| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Reijonen, Joni
VTT Technical Research Centre of Finland
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2024Effect of laser focal point position on porosity and melt pool geometry in laser powder bed fusion additive manufacturingcitations
- 2022High-coercivity NdFeB Printed Magnets With Laser Powder Bed Fusion Method
- 2022Single-Track Laser Scanning as a Method for Evaluating Printability: The Effect of Substrate Heat Treatment on Melt Pool Geometry and Cracking in Medium Carbon Tool Steelcitations
- 2022Laser Powder Bed Fusion Of High Carbon Tool Steels
- 2022Experimental and Calphad Methods for Evaluating Residual Stresses and Solid-State Shrinkage after Solidificationcitations
- 2022Opportunities Of Physics-Based Multi-Scale Modeling Tools In Assessing Intra-Grain Heterogeneities, Polycrystal Properties And Residual Stresses Of AM Metals
- 2021Micromechanical modeling approach to single track deformation, phase transformation and residual stress evolution during selective laser melting using crystal plasticitycitations
- 2021Cross-testing laser powder bed fusion production machines and powders: Variability in mechanical properties of heat-treated 316L stainless steelcitations
- 2021Cross-testing laser powder bed fusion production machines and powderscitations
- 2021Cross-testing laser powder bed fusion production machines and powders:Variability in mechanical properties of heat-treated 316L stainless steelcitations
- 2021Method for embedding components during additive manufacturing of metal parts
- 2020On the effect of shielding gas flow on porosity and melt pool geometry in laser powder bed fusion additive manufacturingcitations
- 2017Feasibility of selective laser melting process in manufacturing of digital spare parts
- 2017Circular Economy Concept In Additive Manufacturing
Places of action
| Organizations | Location | People |
|---|
article
Cross-testing laser powder bed fusion production machines and powders
Abstract
Laser powder bed fusion additive manufacturing is used for demanding applications in industries such as aerospace. However, machine-specific, optimized process conditions and parameters are required to assure consistent part quality. In addition, differences in supplied powder can cause variation in the mechanical properties of the final parts. In this paper, the variability in mechanical properties of 316Lstainless steel produced with two different laser powder bed fusion machines from two different powder batches was studied by producing an identical set of tensile and impact toughness test specimens. The samples were subjected to stress-relieving, solution annealing and hot isostatic pressing to assess the effectiveness of standardized heat-treatments in reducing variation in the mechanical properties of the built parts. Porosity, microstructure, tensile properties, and impact toughness of the specimens were measured to study the effect of changing the material, machine, and heat treatment. The maximum differences observed between the studied machine-powder combinations were approximately 7% for tensile properties and approximately 20% for impact toughness. HIP reduced the variability in all other studied properties except elongation. All the specimens fulfil the minimum requirements set in ASTM F3184-16 for AM 316L.