| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Cieślak, Grzegorz
Institute of Precision Mechanics
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2024Enhanced mechanical properties and microstructural stability of ultrafine-grained biodegradable Zn-Li-Mn-Mg-Cu alloys produced by rapid solifictaion and high-pressure torsioncitations
- 2024Enhanced mechanical properties and microstructural stability of ultrafine-grained biodegradable Zn–Li–Mn–Mg–Cu alloys produced by rapid solidification and high-pressure torsioncitations
- 2023Properties of Ni-B/B Composite Coatings Produced by Chemical Reductioncitations
- 2021Evaluation of Harmonic Structure Obtained in Mechanically Milled Powders and Pulse Plasma Sintered Compacts of Austenitic Steelcitations
- 2020Influence of heat treatment on properties of Ni-B/B composite coatingscitations
- 2019The influence of volume fraction of amorphous phase on corrosion resistance of Mg67Zn29Ca4alloycitations
- 2019Structure and mechanical properties of nanocrystalline Ni/Cu multilayer coatings produced by the electrocrystallization methodcitations
- 2019The impact of different volume fractions of crystalline structures on the electrochemical behaviour of Mg67Zn29Ca4alloys for biomedical applicationscitations
- 2019Demystifying the sluggish diffusion effect in high entropy alloyscitations
- 2019Glass forming ability of Zr48Cu36Al16-xAgx alloys determined by three different methodscitations
- 2018Preparation and properties of nanocrystalline Ni/graphene composite coatings deposited by electrochemical methodcitations
- 2018Studies of “sluggish diffusion” effect in Co-Cr-Fe-Mn-Ni, Co-Cr-Fe-Ni and Co-Fe-Mn-Ni high entropy alloys; determination of tracer diffusivities by combinatorial approachcitations
- 2018Effect of structure on corrosion resistance of Mg-Zn-Ca alloy
- 2017Influence of Cu content on high temperature oxidation behavior of AlCoCrCuxFeNi high entropy alloys (x = 0; 0.5; 1)citations
- 2017Abrasion resistance of Ni-B/Si3N4 composite layers produced by electroless methodcitations
- 2016Preparation and mechanical properties of alumina composites reinforced with nickel-coated graphenecitations
Places of action
| Organizations | Location | People |
|---|
article
Glass forming ability of Zr48Cu36Al16-xAgx alloys determined by three different methods
Abstract
This work was focused on the glass forming ability (GFA) of Zr48Cu36Al16-xAgx alloys (x=0, 2, …, 16) examination using three different methods. Critical diameters were determined by both discrete (classic) and continuous (cone test) methods. Several commonly used GFA thermal indicators were investigated as well. Due to oxygen contamination strong influence on the GFA of Zr-based alloys, oxygen content was measured in each prepared alloy by inert gas fusion method. Additionally, the authors discussed the alloy composition influence on the critical diameters and their respective thermal indicators values. These values were compared and their correlation with critical diameters was evaluated in terms of R2 correlation coefficient values. The best correlation was calculated for the θ indicator (R2=0.979).