| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Whalen, Scott
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (10/10 displayed)
- 2023Solutionization via Severe Plastic Deformationcitations
- 2023Shear Assisted Processing and Extrusion (ShAPE) of Lightweight Automotive Components (CRADA 418)
- 2023Hot Rolling of ZK60 Magnesium Alloy with Isotropic Tensile Properties from Tubing Made by Shear Assisted Processing and Extrusion (ShAPE)citations
- 2023Co-Extrusion of Dissimilar Aluminum Alloys via Shear-Assisted Processing and Extrusioncitations
- 2023Effect of high iron content on direct recycling of unhomogenized aluminum 6063 scrap by Shear Assisted Processing and Extrusioncitations
- 2022Manufacture aluminum alloy tube from powder with a single-step extrusion via ShAPEcitations
- 2022Porosity evolution during heating of copper made from powder by friction extrusioncitations
- 2022Fabrication of Aluminum Alloy 6063 Tubing from Secondary Scrap with Shear Assisted Processing and Extrusioncitations
- 2021Mechanical and microstructural characterization of AZ31 magnesium‑carbon fiber reinforced polymer joint obtained by friction stir interlocking techniquecitations
- 2021Shear Assisted Processing and Extrusion of Aluminum Alloy 7075 Tubing at High Speedcitations
Places of action
| Organizations | Location | People |
|---|
article
Manufacture aluminum alloy tube from powder with a single-step extrusion via ShAPE
Abstract
The mechanical performance of aluminum (Al) in terms of strength, wear, and corrosion resistance, especially high-temperature strength, has been shown to improve with the addition of transition metal (TM) elements of Fe, Cr, and Ti. However, the feedstock of Al-TM alloy occurs as powders. Making extrudate from powders requires multiple procedures and consumes considerable energy. This study developed Shear Assisted Processing and Extrusion (ShAPE) as a single-step process that manufactures tubes directly from Al-TM powders obtained via gas atomization. Meter-long Al-TM alloy tubes are extruded from powders with different processing conditions. The average density of ShAPE tubes is 2.94 kg/cm<sup>3</sup>, equal to or higher than parts fabricated by hot extrusion and sintering. The powder-to-tube fabrication process was revealed and discussed by examining the microstructural evolution. The Vickers hardness of ShAPE tubes ranges from 110 to 140 HV through the wall thickness and at different extrusion speeds. The variation in hardness was correlated with the extent of refinement of intermetallics and attributed to the shear deformation per unit extrusion length. Energy cost analysis shows that ShAPE saves about 60 % energy compared to the traditional sintering and extrusion processes. Results indicate ShAPE is a low-cost, high-efficiency manufacturing process for producing tubes from metallic powders.