| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Pellegrino, Antonio
University of Bath
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (29/29 displayed)
- 2024Strain rate and temperature dependence of short/unidirectional carbon fibre PEEK hybrid compositescitations
- 2024Strain rate and temperature dependence of short/unidirectional carbon fibre PEEK hybrid compositescitations
- 2024A data-driven rate and temperature dependent constitutive model of the compression response of a syntactic foamcitations
- 2024A comprehensive investigation on the temperature and strain rate dependent mechanical response of three polymeric syntactic foams for thermoforming and energy absorption applicationscitations
- 2024A Novel Specimen Design for Multiaxial Loading Experiments at High Strain Ratescitations
- 2023Dynamic response of Advanced Placed Ply compositescitations
- 2023Influence of Strain History on Dynamic Strain Localization and Stress State During High-Rate Tensile Loading of Titanium Alloys:Experiments, Modeling, and Analytical Methodscitations
- 2023A data-driven model of the yield and strain hardening response of commercially pure titanium in uniaxial stresscitations
- 2023Influence of Strain History on Dynamic Strain Localization and Stress State During High-Rate Tensile Loading of Titanium Alloyscitations
- 2022The dependency of compressive response of epoxy syntactic foam on the strain rate and temperature under rigid confinementcitations
- 2022Loading mode and lateral confinement dependent dynamic fracture of a glass ceramic Macorcitations
- 2022Pure shear plastic flow and failure of titanium alloys under quasi-static and dynamic torsional loadingcitations
- 2022Temperature dependent dynamic compressive response of PA66-GF30 composite under constant strain rate multiaxial loadingcitations
- 2022Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of straincitations
- 2021Temperature dependent dynamic strain localization and failure of ductile polymeric rods under large deformationcitations
- 2021Thermomechanical constitutive behaviour of a near α titanium alloy over a wide range of strain ratescitations
- 2021Dynamic necking of a near α titanium alloy at high strain ratescitations
- 2021Measurement of pure shear constitutive relationship from torsion tests under quasi-static, medium, and high strain rate conditionscitations
- 2020Strain rate and temperature dependent strain localization of a near α titanium alloycitations
- 2020Dynamic tensile testing of needle-punched nonwoven fabricscitations
- 2020Rate dependent behaviour and dynamic strain localisation of three novel impact resilient titanium alloyscitations
- 2019A new technique for tensile testing of engineering materials and composites at high strain ratescitations
- 2018Measurements of the effects of pure and salt water absorption on the rate-dependent response of an epoxy matrixcitations
- 2018Effect of particle morphology, compaction, and confinement on the high strain rate behavior of sandcitations
- 2017Bayesian calibration of microCT-based DEM simulations for predicting the effective elastic response of granular materials
- 2017Strain rate dependence of mode II delamination resistance in through thickness reinforced laminated compositescitations
- 2016Effect of strain rate and fibre rotation on the in-plane shear response of ±45° laminates in tension and compression testscitations
- 2016The Dynamic Response of Etnean Sand and the Effect of Its Impingement on Ti-6Al-4 V Alloycitations
- 2015The mechanical response of a syntactic polyurethane foam at low and high rates of straincitations
Places of action
| Organizations | Location | People |
|---|
article
Strain rate and temperature dependent strain localization of a near α titanium alloy
Abstract
<p>The tensile response of a near α Ti3Al2.5V alloy, conceived for jet engine fan containment applications, is characterized by Digital Image Correlation (DIC) technique at quasi-static 0.001 s<sup>−1</sup>, medium rate 12 s<sup>−1</sup> and high strain rates 700 s<sup>−1</sup>-3000 s<sup>−1</sup> at room temperature and elevated temperatures 100°C and 200°C. The material is found to present noticeable strain rate sensitivity. Observations indicate that the dynamic true strain rate in the necking cross-section can reach values up to 10,000 s<sup>−1</sup> due to strain localization. True stress-strain relationship beyond necking at high strain rates presents limited rate dependent response, however, there is clearly no locking of strain rate effect from medium rate to high rates. A series of tests undertaken at elevated temperatures indicate that the higher temperature results in a higher true strain rate for corresponding values of true strain. Experimental results from quasi-static test condition to high strain rates are used to determine an appropriate constitutive model for finite element simulations of the tensile experiments. The model accurately predicts the experimentally dynamic macroscopic force-time response and local true stress-strain relationship, and reveals the increasing trend of true strain rate evolution and decreasing trend of dynamic amplification evolution in good agreement with the experimental measurements with the average absolute relative error less than 8.4 % and the Pearson correlation coefficient larger than 0.957.</p>