| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Syed, Abdul Khadar
Coventry University
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (22/22 displayed)
- 2024Defect tolerance and fatigue limit prediction for laser powder bed fusion Ti6Al4Vcitations
- 2023Fatigue crack growth behavior in an aluminum alloy Al–Mg–0.3Sc produced by wire based directed energy deposition processcitations
- 2023Strain controlled fatigue behaviour of a wire + arc additive manufactured Ti-6Al-4Vcitations
- 2022Cyclic plasticity and damage mechanisms of Ti-6Al-4V processed by electron beam meltingcitations
- 2021Effect of deposition strategies on fatigue crack growth behaviour of wire+ arc additive manufactured titanium alloy Ti-6Al-4Vcitations
- 2021Influence of deposition strategies on tensile and fatigue properties in a wire + arc additive manufactured Ti-6Al-4Vcitations
- 2021Effect of deposition strategies on fatigue crack growth behaviour of wire + arc additive manufactured titanium alloy Ti–6Al–4Vcitations
- 2020High cycle fatigue and fatigue crack growth rate in additive manufactured titanium alloyscitations
- 2020The role of microstructure and local crystallographic orientation near porosity defects on the high cycle fatigue life of an additive manufactured Ti-6Al-4Vcitations
- 2019Microstructure and mechanical properties of as-built and heat-treated electron beam melted Ti–6Al–4Vcitations
- 2019A critical evaluation of the microstructural gradient along the build direction in electron beam melted Ti-6Al-4V alloycitations
- 2019Criticality of porosity defects on the fatigue performance of wire + arc additive manufactured titanium alloycitations
- 2019High cycle fatigue and fatigue crack growth rate in additive manufactured titanium alloyscitations
- 2019Criticality of porosity defects on the fatigue performance of wire + arc additive manufactured titanium alloycitations
- 2019Interrupted fatigue testing with periodic tomography to monitor porosity defects in wire + arc additive manufactured Ti-6Al-4Vcitations
- 2019An experimental study of residual stress and direction-dependence of fatigue crack growth behaviour in as-built and stress-relieved selective-laser-melted Ti6Al4Vcitations
- 2018A comparison of fatigue crack growth performance of two aerospace grade aluminium alloys reinforced with bonded crack retarderscitations
- 2018Experimental and numerical analysis of flexural and impact behaviour of glass/pp sandwich panel for automotive structural applicationscitations
- 2018Mapping residual strain induced by cold working and by laser shock peening using neutron transmission spectroscopycitations
- 2017Fatigue performance of bonded crack retarders in the presence of cold worked holes and interference-fit fasteners
- 2017Fatigue performance of bonded crack retarders in the presence of cold worked holes and interference-fit fastenerscitations
- 2014Durability of bonded crack retarders for aerospace
Places of action
| Organizations | Location | People |
|---|
article
Criticality of porosity defects on the fatigue performance of wire + arc additive manufactured titanium alloy
Abstract
This study was aimed at investigating the effect of internal porosity on the fatigue strength of wire + arc additive manufactured titanium alloy (WAAM Ti-6Al-4V). Unlike similar titanium alloys built by the powder bed fusion processes, WAAM Ti-6Al-4V seldom contains gas pores. However, feedstock may get contaminated that may cause pores of considerable size in the built materials. Two types of specimens were tested: (1) control group without porosity referred to as reference specimens; (2) designed porosity group using contaminated wires to build the specimen gauge section, referred to as porosity specimens. Test results have shown that static strength of the two groups was comparable, but the elongation in porosity group was reduced by 60% and its fatigue strength was 33% lower than the control group. The stress intensity factor range of the crack initiating pore calculated by Murakami’s approach has provided good correlation with the fatigue life. The kink point on the data fitting curve corresponds well with the threshold value of the stress intensity factor range found in the literature. For predicting the fatigue limit, a modified Kitagawa-Takahashi diagram was proposed consisting of three regions depending on porosity size. Critical pore diameter was found to be about 100 µm.