| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Mcgarrigle, Cormac
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (11/11 displayed)
- 2022Influence of extrusion parameters on filled polyphenylsulfone tufting yarns on open-hole tensile strengthcitations
- 2022Characterization of continuous carbon fibre reinforced 3D printed polymer composites with varying fibre volume fractionscitations
- 2022Elastic Modulus and Flatwise (Through-Thickness) Tensile Strength of Continuous Carbon Fibre Reinforced 3D Printed Polymer Compositescitations
- 2021Comparison of Properties and Bead Geometry in MIG and CMT Single Layer Samples for WAAM Applicationscitations
- 2021Influence of Binder Float Length on the Out-of-Plane and Axial Impact Performance of 3D Woven Compositescitations
- 2021Thread-stripping test procedures leading to factors of safety data for friction-drilled holes in thin-section aluminium alloycitations
- 2020Improved crush energy absorption in 3D woven composites by pick density modificationcitations
- 2019Influence of Textile Architecture on the Mechanical Properties of 3D Woven Carbon Composites
- 2019Comparative studies of structure property relationship between glass/epoxy and carbon/epoxy 3D woven composites
- 2019Energy Absorption Mechanisms in Layer-to-Layer 3D Woven Composites
- 2019Improved Energy Absorption in 3D Woven Composites by Weave Parameter Manipulationcitations
Places of action
| Organizations | Location | People |
|---|
article
Characterization of continuous carbon fibre reinforced 3D printed polymer composites with varying fibre volume fractions
Abstract
Fused deposition modelling (FDM) is one of the most popular additive manufacturing (AM) technique which is used to investigate the elastic properties of 3D printed polyamide-based polymer composites structures. The aim of this work is to study the mechanical properties of continuous carbon fibre reinforced polyamide polymer composite samples using tensile and flexural testing by varying the fibre volume contents with applying pressure, temperature and holding the samples for 60 minutes in the platen press. The results showed that the strength and stiffness increased with the increase in fibre volume content (fraction). Hot pressed samples exhibited the increase in tensile strength by about 27 % and elastic modulus by 11 % because of increasing the fibre volume fraction from 29 % to 35%. Synergetic effect of both short and continuous carbon fibre was also studied, and it was observed that the tensile properties were higher for the samples reinforced with short and continuous fibre than only continuous fibre polymer composites. Effects of voids on 3D printed continuous carbon fibre-reinforced polymer composites were quantified. A microstructure study of the 3D printed polymer composites was carried out using scanning electron microscope (SEM). Following SEM analysis on the tested specimens, it was observed that there was a strong correlation between the mechanical properties and the microstructure. Fibre volume fraction was measured using acid digestion method to determine the amount of fibre contents before and after hot pressing (compaction). From Micro- Computed Tomography (µCT) it was confirmed that hot pressing reduced the void content which in return increased the strength and modulus.