| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Reis, P.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (12/12 displayed)
- 2014Impact strength of composites with nano-enhanced resin after fire exposurecitations
- 2013Impact response of Kevlar composites with nanoclay enhanced epoxy matrixcitations
- 2012Low-velocity impact response of non-woven hemp fibre reinforced unsaturated polyester composites: Influence of impactor geometry and impact velocitycitations
- 2012Evaluation of water absorption damage in hemp fibre reinforced unsaturated polyester composites by the nanoindentation testingcitations
- 2007A note on tribological behaviour of α-sialon/steel couples under dry conditionscitations
- 2006Friction and wear behaviour of β-silicon nitride-steel couples under unlubricated conditionscitations
- 2006Cutting performance of time-modulated chemical vapour deposited diamond coated tool inserts during machining graphitecitations
- 2005Wear behavior on advanced structural ceramics: α-sialon matrix reinforced with β-sialon fiberscitations
- 2005Tribological behaviour of colloidally processed sialon ceramics sliding against steel under dry conditionscitations
- 2004A study on milling of glass fiber reinforced plastics manufactured by hand-lay up using statistical analysis (ANOVA)citations
- 2004Drilling fiber reinforced plastics (FRPs) manufactured by hand lay-up: influence of matrix (Viapal VUP 9731 and ATLAC 382-05)citations
- 2004Experimental study of drilling glass fiber reinforced plastics (GFRP) manufactured by hand lay-upcitations
Places of action
| Organizations | Location | People |
|---|
article
A study on milling of glass fiber reinforced plastics manufactured by hand-lay up using statistical analysis (ANOVA)
Abstract
Milling is the most practical machining (corrective) operation for removing excess material to produce a well defined and high quality surface. However, milling composite materials presents a number of problems such as surface delamination associated with the characteristics of the material and the cutting parameters used. In order to minimize these problem is presented a study with the objective of evaluating the cutting parameters (cutting velocity and feed rate) related to machining force in the workpiece, delamination factor, surface roughness and international dimensional precision in two GFRP composite materials (Viapal VUP 9731 and ATLAC 382-05). A plan of experiments, based on an orthogonal array, was established considering milling with prefixed cutting parameters. Finally an analysis of variance (ANOVA) was preformed to investigate the cutting characteristics of GFRP composite materials using a cemented carbide (K10) end mill.