| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Kruszewski, Mirosław
Warsaw University of Technology
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2024Microstructure and Corrosion of Mg-Based Composites Produced from Custom-Made Powders of AZ31 and Ti6Al4V via Pulse Plasma Sinteringcitations
- 2024A comparative study of oxidation behavior of Co4Sb12 and Co4Sb10.8Se0.6Te0.6 skutterudite thermoelectric materials fabricated via fast SHS-PPS routecitations
- 2023Rapid fabrication of Se-modified skutterudites obtained via self-propagating high-temperature synthesis and pulse plasma sintering routecitations
- 2023In-depth analysis of the influence of bio-silica filler (Didymosphenia geminata frustules) on the properties of Mg matrix compositescitations
- 2022Thermoelectric properties of bismuth-doped magnesium silicide obtained by the self-propagating high-temperature synthesiscitations
- 2022Heat Treatment of NiTi Alloys Fabricated Using Laser Powder Bed Fusion (LPBF) from Elementally Blended Powderscitations
- 2022Influence of Ag particle shape on mechanical and thermal properties of TIM jointscitations
- 2022A comparison of the microstructure-dependent corrosion of dual-structured Mg-Li alloys fabricated by powder consolidation methods: Laser powder bed fusion vs pulse plasma sinteringcitations
- 2022Pressureless Direct Bonding of Au Metallized Substrate with Si Chips by Micro-Ag Particlescitations
- 2021Microstructure and Thermoelectric Properties of Doped FeSi2 with Addition of B4C Nanoparticlescitations
- 2020Thermoelectric properties of Cu2S obtained by high temperature synthesis and sintered by IHP methodcitations
- 2019Microstructure and thermoelectric properties of p and n type doped β-FeSi2 fabricated by mechanical alloying and pulse plasma sinteringcitations
- 2018Skutterudite (CoSb3) thermoelectric nanomaterials fabricated by Pulse Plasma in Liquidcitations
- 2017Design of interfacial Cr 3 C 2 carbide layer via optimization of sintering parameters used to fabricate copper/diamond composites for thermal management applicationscitations
- 2014Thermal conductivity enhancement of copper–diamond composites by sintering with chromium additivecitations
- 2011W/steel joint fabrication using the pulse plasma sintering (PPS) methodcitations
Places of action
| Organizations | Location | People |
|---|
article
Rapid fabrication of Se-modified skutterudites obtained via self-propagating high-temperature synthesis and pulse plasma sintering route
Abstract
Selenium is an effective dopant in skutterudite-based thermoelectric materials. It strongly influences thermaltransport properties due to effective phonon scattering. This study proposes a short-term fabrication route to SemodifiedCoSb3-based materials. Alloy synthesis was conducted via self-propagating high-temperature synthesis.Subsequently, pulse plasma sintering consolidated all materials. As a result, thermoelectric materials with highelectrical properties homogeneity were obtained. Seebeck potential mapping showed the measured deviation ofthe Seebeck coefficient for all fabricated samples was between 5 and 7%. A very low thermal conductivity (1.59W mက00 1 Kက00 1, at 573 K) was achieved for the highest doped sample, and one of the lowest reported results obtainedfor bulk skutterudite-based thermoelectric materials ever. This resulted in a low lattice thermal conductivity(1.51 W mက00 1 Kက00 1, at 573 K). This led to the highest ZT (0.27 at 623 K) for the highest doped sample.