| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Żrodowski, Łukasz
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (12/12 displayed)
- 2024Microstructure and Corrosion of Mg-Based Composites Produced from Custom-Made Powders of AZ31 and Ti6Al4V via Pulse Plasma Sinteringcitations
- 2024Polymer‐based filaments with embedded magnetocaloric <scp>Ni‐Mn‐Ga</scp> Heusler alloy particles for additive manufacturingcitations
- 2023How to control the crystallization of metallic glasses during laser powder bed fusion? Towards part-specific 3D printing of in situ compositescitations
- 2023Selective Laser Melting of Fe-Based Metallic Glasses With Different Degree of Plasticitycitations
- 2023Atomisation of Ti-6Ta-1.5Zr-0.2Ru-5Cu (wt%) for additive manufacturing for biomedical applicationscitations
- 2022A comparison of the microstructure-dependent corrosion of dual-structured Mg-Li alloys fabricated by powder consolidation methods: Laser powder bed fusion vs pulse plasma sinteringcitations
- 2022How to Control the Crystallization of Metallic Glasses During Laser Powder Bed Fusion? Towards Part-Specific 3d Printing of in Situ Composites
- 2021Ultrashort Sintering and Near Net Shaping of Zr-Based AMZ4 Bulk Metallic Glasscitations
- 2021Microstructure and magnetic properties of selected laser melted Ni-Mn-Ga and Ni-Mn-Ga-Fe powders derived from as melt-spun ribbons precursorscitations
- 2020Analysis of Microstructure and Properties of a Ti–AlN Composite Produced by Selective Laser Meltingcitations
- 2019New approach to amorphization of alloys with low glass forming ability via selective laser meltingcitations
- 2016The Novel Scanning Strategy For Fabrication Metallic Glasses By Selective Laser Melting
Places of action
| Organizations | Location | People |
|---|
article
How to control the crystallization of metallic glasses during laser powder bed fusion? Towards part-specific 3D printing of in situ composites
Abstract
This paper describes a strategy for creating highly oriented crystalline-amorphous composites using the laser powder bed fusion (LPBF) process. The strategy involves using a novel two-stage melting approach and ultra-high-pressure hot isostatic pressing (HIP) on well-known AMZ4 (Zr59.3Cu28.8Al10.4Nb1.5) and equiatomic CuZr amorphous alloys.The experiments demonstrate that by the fine-tuning laser parameters, allowed to obtain parts with purely amorphous material and to create geometry-specific microstructural design composites based on laminate amorphous-crystalline structure. This approach also provides novel opportunities for nonequilibrium phase distribution design by controlling local crystallization in the heat-affected zone (HAZ) and avoiding heat accumulation. Additionally, the porous amorphous material can be densified without crystallization using HIP at a temperature near the supercooled liquid region.The distribution of the crystalline phase created during LPBF and crystallization on pre-induced nuclei during HIP was proven to be a critical factor for composite properties. Wear and bending tests reveal the influence of crystalline-amorphous layers orientation on mechanical properties. The functional demonstrators were manufactured to show the possibilities in the design for additive manufacturing (DfAM) with a microstructure-designed composites.