| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Atkinson, Michael
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (19/19 displayed)
- 2023The role of hydrides and precipitates on the strain localisation behaviour in a zirconium alloycitations
- 2023The role of hydrides and precipitates on the strain localisation behaviour in a zirconium alloycitations
- 2022A novel method for radial hydride analysis in zirconium alloys:HAPPycitations
- 2022A novel method for radial hydride analysis in zirconium alloyscitations
- 2022Slip activity during low-stress cold creep deformation in a near-α titanium alloycitations
- 2022Slip activity during low-stress cold creep deformation in a near-α titanium alloycitations
- 2021The Effect of Loading Direction on Slip and Twinning in an Irradiated Zirconium Alloycitations
- 2021Understanding the role of local texture variation on slip activity in a two-phase titanium alloycitations
- 2021Understanding the role of local texture variation on slip activity in a two-phase titanium alloycitations
- 2020A statistical study of the relationship between plastic strain and lattice misorientation on the surface of a deformed Ni-based superalloy
- 2020Comparison of sub-grain scale digital image correlation calculated using commercial and open-source software packagescitations
- 2020Measurement of local plastic strain during uniaxial reversed loading of nickel alloy 625
- 2019Characterisation of irradiation enhanced strain localisation in a zirconium alloycitations
- 2019Characterisation of irradiation enhanced strain localisation in a zirconium alloycitations
- 2019Identification of active slip mode in a hexagonal material by correlative scanning electron microscopycitations
- 2019Identification of active slip mode in a hexagonal material by correlative scanning electron microscopycitations
- 2019Comparing local deformation measurements to predictions from crystal plasticity during reverse loading of an aerospace alloy
- 2018On the ductility of alpha titanium: The effect of temperature and deformation modecitations
- 2018On the ductility of alpha titanium: The effect of temperature and deformation modecitations
Places of action
| Organizations | Location | People |
|---|
article
The role of hydrides and precipitates on the strain localisation behaviour in a zirconium alloy
Abstract
In service, zirconium alloys undergo aqueous corrosion and hydrogen is absorbed, which can lead to the formation of hydrides. Hydrides, as well as the precipitates in zirconium alloys, affect the mechanical performance, though their contribution to plasticity is not yet understood. This study uses a combination of high-resolution digital image correlation and electron backscatter diffraction to quantify the strain partitioning between the different phases. Following uniaxial tensile deformation, it was found that the average strain within the δ-ZrH and Zr(Fe,Cr)2 was lower than in the α-Zr. Shear bands in the α-Zr matrix were observed to interact with small and medium sized hydride in multiple ways, such as terminating at the interface, cracking and shear around the interface or causing plastic slip in the hydride. Large hydrides showed a particularly detrimental effect on deformation behaviour, with large strain localisations and cracking observed at interfaces, which are typically precursors to failure. In contrast, the Zr(Fe,Cr)2 precipitates remained undeformed and forced the expected metal-matrix lattice rotation. The importance of these observations in context of fuel cladding integrity is discussed.