| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Chanakyan, C.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (3/3 displayed)
- 2024Characterization of annealed‐silane modified barley husk biosilica and garment waste cotton microfiber vinyl ester compositecitations
- 2022Influence of Nanoclay Filler Material on the Tensile, Flexural, Impact, and Morphological Characteristics of Jute/E-Glass Fiber-Reinforced Polyester-Based Hybrid Composites: Experimental, Modeling, and Optimization Studycitations
- 2021Optimization of FSP Process Parameters on AA5052 Employing the S/N Ratio and ANOVA Methodcitations
Places of action
| Organizations | Location | People |
|---|
article
Characterization of annealed‐silane modified barley husk biosilica and garment waste cotton microfiber vinyl ester composite
Abstract
<jats:title>Abstract</jats:title><jats:sec><jats:label /><jats:p>This study investigates the effect of adding annealed‐silane modified biosilica and waste cotton microfiber into the vinyl‐based composite on load‐bearing properties. The primary objective of this study was to unveil the significance of annealing treatment on the biosilica and its effect on composite's properties. The biosilica was prepared from waste barely husk ash and the waste cotton microfiber was used as received. The composites were fabricated using mold casting method and their properties were assessed in accordance with ASTM standards. Among the composites examined, the VCB2 displays improved mechanical properties with a highest tensile strength of 120 MPa. In contrast, the VCB3 composite exhibited enhanced hardness with a low specific wear rate of 0.22 mm<jats:sup>3</jats:sup>/N m and a coefficient of friction of 0.19. Furthermore, the composite VCB3 demonstrated an elevated dielectric constant of 3.85 and a low dielectric loss of 0.136 with a high thermal stability up to 388°C. This study underscores the potential of annealing process on biosilica and its stress free grain structure in property improvement made as valuable reinforcement in waste cotton microfiber‐vinyl ester composites, opening up new avenues for diverse engineering applications with advanced material performance.</jats:p></jats:sec><jats:sec><jats:title>Highlights</jats:title><jats:p><jats:list list-type="bullet"> <jats:list-item><jats:p>Vinyl ester composites are prepared from waste biomass biosilica and cotton microfiber.</jats:p></jats:list-item> <jats:list-item><jats:p>Addition of biosilica improved the void filling effect of matrix.</jats:p></jats:list-item> <jats:list-item><jats:p>Addition of biosilica improved the mechanical properties.</jats:p></jats:list-item> <jats:list-item><jats:p>Addition of biosilica up to 3 vol.% improved the wear properties.</jats:p></jats:list-item> <jats:list-item><jats:p>Addition of biosilica up to 3 vol.% improved the thermal stability.</jats:p></jats:list-item> </jats:list></jats:p></jats:sec>