| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Stalin, B.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (10/10 displayed)
- 2022[Retracted] Examining Impacts of Acidic Bath Temperature on Nano-Synthesized Lead Selenide Thin Films for the Application of Solar Cellscitations
- 2021Evaluation of mechanical, thermal and water absorption behaviors of Polyalthia longifolia seed reinforced vinyl ester compositescitations
- 2021Applicability of cellulosic-based Polyalthia longigolia seed filler reinforced vinyl ester biocomposites on tribological performance
- 2021Effect of Graphene Oxide-Boron Nitride-Based Dual Fillers on Mechanical Behavior of Epoxy/Glass Fiber Compositescitations
- 2021Investigations on Microstructure, Mechanical, Thermal, and Tribological Behavior of Cu-MWCNT Composites Processed by Powder Metallurgycitations
- 2020Evaluation of mechanical, thermal and water absorption behaviors of Polyalthia longifolia seed reinforced vinyl ester compositescitations
- 2020Applicability of cellulosic-based Polyalthia longigolia seed filler reinforced vinyl ester biocomposites on tribological performancecitations
- 2020Optimization of powder metallurgy parameters of TiC- and B4C-reinforced aluminium composites by Taguchi methodcitations
- 2020A Study On development of Induction Welding of Thermoplastic Compositescitations
- 2020Investigations on microstructure and mechanical properties of Mg-5wt.% Cu-TiB2 composites produced via powder metallurgy routecitations
Places of action
| Organizations | Location | People |
|---|
article
Applicability of cellulosic-based Polyalthia longigolia seed filler reinforced vinyl ester biocomposites on tribological performance
Abstract
The focus of this work was to analyze the effect of weight percentage (wt.%) of Polyalthia longigolia seed filler (PLSF) on the wear responses (wear loss and coefficient of friction) of the vinyl ester (VE) matrix composites, using signal-to-noise (SN) ratio and analysis of variance (ANOVA) methods. The Polyalthia longigolia seed filler/vinyl ester (PLSF-VE) composites were produced by compression molding (CM) technique. Scanning electron microscopy (SEM) analysis showed that the PLSF content was homogeneously distributed in the matrix. Pin on disc (POD) wear tester was employed to carry out the experiments. Both SN ratio and ANOVA were performed to determine the process parameters that exhibited lower wear responses. The wear of the composite was minimized by optimizing the four diverse process factors: load, P (N), sliding speed, N (rpm) and filler content (wt.%), based on Taguchi's L9 orthogonal array. The process parameters at which minimum wear loss (WL) occurred were identified with 25 wt.% sample at 10 N and 300 rpm. Also, the process parameters for minimum coefficient of friction (COF) were observed with 25 wt.% sample at 5 N and 700 rpm.From the ANOVA results obtained, it was evident that P mostly influenced the WL and COF of the PLSF-VE composites during POD wear testing. This kind of lightweight composite can be a suitable alternative for small scale loading conditions, such as brake pads and clutch plates in the automobile industry.