| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Keränen, Janne T.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (7/7 displayed)
- 2024Air-laid and foam-laid nonwoven compositescitations
- 2024Development and Characterization of Poly(butylene succinate-co-adipate)/Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) with Cowpea Lignocellulosic Fibers as a Filler via Injection Molding and Extrusion Film-Castingcitations
- 2023Properties of Bio-Composite Packaging Materials Developed Using Cowpea Lignocellulosic Sidestream as a Filler
- 2023Agricultural sidestream as a biomaterial commodity: opportunities and challenges
- 2023Faba bean lignocellulosic sidestream as a filler for the development of biodegradable packagingcitations
- 2020Feasibility of foam forming technology for producing wood plastic compositescitations
- 2009Some insight on paper structure and properties with different drying conditions
Places of action
| Organizations | Location | People |
|---|
article
Development and Characterization of Poly(butylene succinate-co-adipate)/Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) with Cowpea Lignocellulosic Fibers as a Filler via Injection Molding and Extrusion Film-Casting
Abstract
Biodegradable poly(butylene succinate-co-adipate)/Poly(3-hydroxybutyrate-co-3-hydoxyvalerate) (PBSA/PHBV) filled with lignocellulosic sidestream/fibers from cowpea, a neglected and underutilized African crop are produced by injection molding and extrusion film casting. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) suggests that the fibers have more affinity and interfacial interaction with PBSA than PHBV. This is shown by a decrease in dampening of PBSA and an increase in dampening of PHBV with fiber addition. In addition, fiber addition results in more homogeneous crystal morphology of PBSA, while resulting in more heterogeneous crystal morphology of PHBV. The tensile strength of injection molded bio-composites increases with fiber addition due to good interfacial adhesion between the matrix and fibers revealed by scanning electron microscope. In contrast, the tensile strength of bio-composite films decreases with fiber addition due to the high-volume fraction of pores in bio-composite films that act as stress raisers. The stiffness of both injection molded, and bio-composite films increase with fiber addition, as revealed by an increase in Young's modulus and storage modulus, while the tensile strain decreases. In conclusion, low-value cowpea sidestream can be used as a filler to produce injection molded bio-composites and bio-composite films for potential application as rigid and flexible packaging.