| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Mizera, Jaroslaw
Warsaw University of Technology
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (18/18 displayed)
- 2024Microstructural, corrosion and mechanical properties of a WE43 alloy: conventional extrusion versus SPDcitations
- 2023Comparison of the performance properties of commercially produced roller cone bit coatingscitations
- 2023Impact of an Aluminization Process on the Microstructure and Texture of Samples of Haynes 282 Nickel Alloy Produced Using the Direct Metal Laser Sintering (DMLS) Techniquecitations
- 2022Increasing the Mechanical Strength and Corrosion Resistance of Aluminum Alloy 7075 via Hydrostatic Extrusion and Agingcitations
- 2022The Effect of Extrusion Ratio on the Corrosion Resistance of Ultrafine-Grained Mg-4Li-3Al-Zn Alloy Deformed Using Extrusion with a Forward-Backward Oscillating Diecitations
- 2022Microstructure and corrosion resistance characteristics of Ti–AlN composite produced by selective laser meltingcitations
- 2022Evolution of microstructure dependent corrosion properties of ultrafine AZ31 under conditions of extrusion with a forward backward oscillating diecitations
- 2022A comparison of the microstructure-dependent corrosion of dual-structured Mg-Li alloys fabricated by powder consolidation methods: Laser powder bed fusion vs pulse plasma sinteringcitations
- 2022Effect of annealing on the mechanical and corrosion properties of 316L stainless steel manufactured by laser powder bed fusioncitations
- 2022Corrosion behavior of fine-grained Mg-7.5Li-3Al-1Zn fabricated by extrusion with a forward-backward rotating die (KoBo)citations
- 2022The Impact of Retained Austenite on the Mechanical Properties of Bainitic and Dual Phase Steelscitations
- 2021Microstructure and corrosion resistance of a duplex structured Mg–7.5Li–3Al–1Zncitations
- 2021Influence of bimodal grain size distribution on the corrosion resistance of Mg–4Li–3Al–1Zn (LAZ431)citations
- 2021Analysis of direct metal laser sintering ‒ DMLS and heat treatment influence on the Inconel 713C nickel alloy structurecitations
- 2021Studies of Bainitic Steel for Rail Applications Based on Carbide-Free, Low-Alloy Steelcitations
- 2021Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloyscitations
- 2020The analysis of microstructure and texture evolution in polycrystal and single crystals of nickel after hydrostatic extrusion processcitations
- 2020Influence of Plasma Nitriding on Microstructure of Nickel Superalloy Haynes 282
Places of action
| Organizations | Location | People |
|---|
article
Microstructure and corrosion resistance characteristics of Ti–AlN composite produced by selective laser melting
Abstract
The aim of this study is to produce Ti–AlN via selective laser melting. The results show that the microstructure of the produced alloy is not uniform. The X‐ray diffraction measurements show that the Ti–AlN composite is composed of a Ti matrix, AlN compounds, as well as (TiN)0.88, Al6 Ti19, and Al1.1Ti0.9 intermetallics. The as‐printed Ti–AlN is also composed of dendrites of two typical titanium nitrides (TiN and Ti2N) and titanium aluminum nitride (Ti2AlN). Subsequent quenching and annealing slightly change the phase composition of the alloy and is the main reason for their different corrosion behaviors in acidic and chloride‐containing solutions. The results of this study show that the formation of Al‐rich ternary phases improved the corrosion resistance of the three‐dimensional‐printed Ti–AlN after quenching.