| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Alil, Ana
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (23/23 displayed)
- 2024Non-destructive evaluation of cavitation erosion behavior of alumina-based ceramic materials
- 2024Cavitation erosion monitoring of 42CrMo4 steel samples using the image and morphological analysis
- 2024Comparative investigation of ultrasonic cavitation erosion for two engineering materials ; Uporedno ispitivanje ultrazvučne kavitacione erozije dva inženjerska materijalacitations
- 2024Cavitation resistance of explosively welded aluminium/steel jointcitations
- 2024Cavitation Erosion Resistance Behavior of Some Refractory Ceramics
- 2024Comparative investigation of ultrasonic cavitation erosion for two engineering materialscitations
- 2023Application of image analysis for cavitation erosion monitoring of some engineering materials
- 2023Non-Destructive Examination for Cavitation Resistance of Talc-Based Refractories with Different Zeolite Types Intended for Protective Coatingscitations
- 2023Application of image analysis for cavitation erosion resistance monitoring of some engineering materials
- 2023Influence of Cold Rolling and Annealing on the Mechanical and Corrosion Properties of an AA5182 Al-Mg Alloy
- 2023Cavitation erosion resistance of some engineering materials
- 2023Cavitation erosion resistance of refractory ceramics for foundry coatings application
- 2022X-Ray analysis by Williamson-Hall and stereological analysis of mechanically alloyed Cu-Zr-B alloys
- 2020High temperature materials: properties, demands and applicationscitations
- 2018Mechanical and corrosion properties of AA5083 alloy sheets produced by accumulative roll bonding (ARB) and conventional cold rolling (CR)citations
- 2017Long-term and low-temperature annealing of as-continuous drive friction welded and post-weld heat treated Al/Cu bimetal joints
- 2014Influence of an accumulative roll bonding (ARB) process on the properties of AA5083 Al-Mg alloy sheetscitations
- 2013The effects of aging on the precipitation of the W-rich phase in the matrix of the 92.5W-5Ni-2,5Fe powder metallurgy heavy alloys
- 2012Stress corrosion cracking of an Al-Zn-Mg-Cu alloy after different precipitation hardening treatments
- 2012Corrosion behaviour of an Al-Zn-Mg-Cu alloy after different heat treatments
- 2012Corrosion Testing of an Al-Zn-Mg-Cu Alloy After Different Heat Treatment Regimes by the Application of Electrochemical Methods
- 2011Assessment of Safety Valve Springs Failure
- 2011Plastic deformation and heat treatment of thin walled centrifugally cast high strength crmonb steel tubes
Places of action
| Organizations | Location | People |
|---|
article
Mechanical and corrosion properties of AA5083 alloy sheets produced by accumulative roll bonding (ARB) and conventional cold rolling (CR)
Abstract
<jats:sec><jats:label /><jats:p>Influence of accumulative roll bonding (ARB) and conventional cold rolling (CR) on the mechanical and corrosion properties of AA5083 alloy sheets has been studied. Tensile tests showed significant increase in strength and a decrease in elongation after each ARB deformation and cold rolling reductions. Results of nitric acid mass loss test (NAMLT) revealed that cold rolled and ARB processed specimens were resistant toward intergranular corrosion (IGC) in as‐deformed state. However, after 7 days of sensitization at 100 and 150 °C, cold rolled material became IGC sensitive, while ARB specimens stayed IGC resistant. IGC susceptibility can be correlated with different morphology and distribution of β‐phase (Mg<jats:sub>2</jats:sub>Al<jats:sub>3</jats:sub>) precipitated during sensitization. It was found that extensive shear banding contributed a favorable distribution of β‐phase precipitates in the structure of IGC resistant ARB processed specimens. In case of IGC susceptible conventionally cold rolled specimens, large amount of β‐phase precipitated preferentially along the elongated grain boundaries. Electrochemical parameters were in a good correlation with the results of NAML tests, which in turn, confirmed the superiority of ARB multilayered structure over conventional cold rolled structure in terms of IGC susceptibility and corrosion stability.</jats:p></jats:sec>