| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Ura-Bińczyk, Ewa
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (12/12 displayed)
- 2021Effect of microstructural features on the corrosion behavior of severely deformed Al–Mg–Si alloycitations
- 2020The Influence of Microstructure on Corrosion Resistance of Mg-3Al-1Zn-15Li (LAZ1531) Alloycitations
- 2019Microstructure and corrosion resistance of warm sprayed titanium coatings with polymer sealing for corrosion protection of AZ91E magnesium alloycitations
- 2019Corrosion Resistance of Aluminum Coatings Deposited by Warm Spraying on AZ91E Magnesium Alloycitations
- 2019Mechanical properties and corrosion resistance of hydrostatically extruded 316 LVM stainless steel after low-temperature plasma nitridingcitations
- 2019The effect of grain size and grain boundary misorientation on the corrosion resistance of commercially pure aluminiumcitations
- 2017Mechanical properties and corrosion resistance of ultrafine grained austenitic stainless steel processed by hydrostatic extrusioncitations
- 2017Microstructure and Corrosion Behavior of the Friction Stir Welded Joints Made from Ultrafine Grained Aluminumcitations
- 2017Comparison of corrosion resistance of glass fiber reinforced composites and steels applicable for extraction pipes
- 2017The influence of grain refinement on the corrosion rate of carbon steels in fracturing fluids used in shale gas productioncitations
- 2016Analiza warstw korozyjnych w stalach wykorzystywanych w przemyśle wydobywczym po badaniach korozji naprężeniowej — Analysis of corrosive layers formed on the steels used in oil industry after stress corrosion cracking tests
- 2011Passivation of Al–Cr–Fe and Al–Cu–Fe–Cr complex metallic alloys in 1 M H2SO4 and 1 M NaOH solutionscitations
Places of action
| Organizations | Location | People |
|---|
article
The influence of grain refinement on the corrosion rate of carbon steels in fracturing fluids used in shale gas production
Abstract
Corrosion tests were carried out to study the corrosive behaviour of medium carbon steels with a ferrite–pearlite microstructure during exposure to a synthetic flowback facturing fluid saturated with carbon dioxide. Metallographic investigations, screening tests, surface morphology investigations and identification of surface products were used for this purpose. The results obtained indicate that the corrosion of N80-1 carbon steel was significantly lower than that of K55 carbon steel. The layer of corrosion products consisted of an outer layer of carbonates and an inner layer with cementite lamellas. Higher grain refinement of N80-1 steel compared to that of K55 steel caused the formation of a denser, more homogenous layer of corrosion products, which significantly reduced the corrosion of the base material.