| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Paolella, Andrea
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (8/8 displayed)
- 2024Screen-Printed Composite LiFePO4-LLZO Cathodes Towards Solid-State Li-ion Batteriescitations
- 2024Influence of 3D structural design on the electrochemical performances of Aluminum metal as anode for Li‐ion batteriescitations
- 2023Biomass-derived carbon–silicon composites (C@Si) as anodes for lithium-ion and sodium-ion batteries: A promising strategy towards long-term cycling stability: A mini review
- 2023Biomass-derived carbon–silicon composites (C@Si) as anodes for lithium-ion and sodium-ion batteries:A promising strategy towards long-term cycling stability: A mini reviewcitations
- 2020Direct observation of lithium metal dendrites with ceramic solid electrolytecitations
- 2020Toward an All‐Ceramic Cathode–Electrolyte Interface with Low‐Temperature Pressed NASICON Li<sub>1.5</sub>Al<sub>0.5</sub>Ge<sub>1.5</sub>(PO<sub>4</sub>)<sub>3</sub> Electrolytecitations
- 2020Toward an All-Ceramic Cathode-Electrolyte Interface with Low-Temperature Pressed NASICON Li1.5Al0.5Ge1.5(PO4)3 Electrolytecitations
- 2020Electrospun Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</sub> Nanofibers to Develop Solid-State Electrolytes for Lithium Metal Batteries
Places of action
| Organizations | Location | People |
|---|
article
Toward an All‐Ceramic Cathode–Electrolyte Interface with Low‐Temperature Pressed NASICON Li<sub>1.5</sub>Al<sub>0.5</sub>Ge<sub>1.5</sub>(PO<sub>4</sub>)<sub>3</sub> Electrolyte
Abstract
<jats:title>Abstract</jats:title><jats:p>This work shows, for the first time, the critical influence of pressure during the hot sintering stage on the ionic conductivity of the lithium super ionic conductor Li<jats:sub>1.5</jats:sub>Al<jats:sub>0.5</jats:sub>Ge<jats:sub>1.5</jats:sub>(PO<jats:sub>4</jats:sub>)<jats:sub>3</jats:sub>. A hot press method is developed to obtain high ionic conductivities at the significantly decreased densification temperature of only 650 °C by applying pressure (56 MPa). Considering the possible initiation of undesirable decomposition reactions when cathode materials are annealed at high temperature (typically ≥700 °C), the use of high pressure at 650 °C can significantly limit the formation of degradation by‐products. This study determines the criteria required to optimize the pressure and temperature parameters for enhancing the total ionic conductivity. Finally, this study reports an all solid‐state battery based on a LiFePO<jats:sub>4</jats:sub> olivine cathode prepared at 650 °C showing very good Li‐intercalation/deintercalation performance. Good ionic interfacial contact is achieved without using polymer and liquid electrolyte.</jats:p>