| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Padovano, Elisa
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (22/22 displayed)
- 2024Physics-Informed Neural Networks: a step towards data-driven optimization of additive manufacturing
- 2024Selective Laser Sintering versus Multi Jet Fusion: A Comprehensive Comparison Study Based on the Properties of Glass Beads‐Reinforced Polyamide 12citations
- 2024A Comprehensive Review of Laser Powder Bed Fusion in Jewelry: Technologies, Materials, and Post-Processing with Future Perspectivecitations
- 2024CuCrZr alloy obtained via electron-beam powder bed fusion: Microstructural insights and precipitation behaviour
- 2024Laser Powder Bed Fusion of Pure Titanium: Optimization of Processing Parameters by Means of Efficient Volumetric Energy Density Approach
- 2023Processability of A6061 Aluminum Alloy Using Laser Powder Bed Fusion by In Situ Synthesis of Grain Refinerscitations
- 2023Design and Characterization of Innovative Gas-Atomized Al-Si-Cu-Mg Alloys for Additive Manufacturingcitations
- 2023Optimization of Process Parameters for CuCrZr Alloy Manufactured by Electron Beam Powder Bed Fusion Technologycitations
- 2022Experimental Characterization and Modeling of 3D Printed Continuous Carbon Fibers Composites with Different Fiber Orientation Produced by FFF Processcitations
- 2020Mechanical recycling of an end-of-life automotive composite componentcitations
- 2020Innovative processing route combining fused deposition modelling and laser writing for the manufacturing of multifunctional polyamide/carbon fiber compositescitations
- 2019Laser Treatments for Improving Electrical Conductivity and Piezoresistive Behavior of Polymer–Carbon Nanofiller Compositescitations
- 2019Electrical and Thermal Conductivity of Epoxy-Carbon Filler Composites Processed by Calendaringcitations
- 2018Effect of ZrB2 addition on the oxidation behavior of Si-SiC-ZrB2 composites exposed at 1500°C in aircitations
- 2017Novel Magnesium Elektron21-AlN Nanocomposites Produced by Ultrasound-Assisted Casting; Microstructure, Thermal and Electrical Conductivitycitations
- 2017Effect of Solution Treatment on Precipitation Behaviors, Age Hardening Response and Creep Properties of Elektron21 Alloy Reinforced by AlN Nanoparticlescitations
- 2016Fabrication and characterization of laminated SiC composites reinforced with graphene nanoplateletscitations
- 2015Ceramic multilayer based on ZrB2/SiC system for aerospace applications.
- 2013Microstructure and mechanical properties of milled fibre/SiC multilayer composites prepared by tape casting and pressureless sinteringcitations
- 2013Pressureless sintering of ZrB2–SiC composite laminates using boron and carbon as sintering aidscitations
- 2013Thermophysical properties of SiC multilayer prepared by tape casting and pressureless sinteringcitations
- 2012Microstructure and mechanical properties of short carbon fibre/SiC multilayer composites prepared by tape castingcitations
Places of action
| Organizations | Location | People |
|---|
article
Selective Laser Sintering versus Multi Jet Fusion: A Comprehensive Comparison Study Based on the Properties of Glass Beads‐Reinforced Polyamide 12
Abstract
<jats:p>Selective laser sintering (SLS) and multi jet fusion (MJF) are the most widespread powder bed fusion additive manufacturing techniques for fabricating polymeric parts since they offer great design flexibility, productivity, and geometrical accuracy. However, these technologies differ in the thermal energy source used to melt the powders as well as the innovative use of printing agents featured in the latter one to promote material consolidation and to avoid thermal bleeding at the part contours. The use of a single powder made of glass beads‐reinforced polyamide 12 (PA12/GB) for the fabrication of MJF and SLS samples makes possible a systematic comparison of the printed parts properties. A thoughtful analysis of the microstructure and mechanical properties of the samples reveals differences and peculiarities between the two technologies. SLS exhibits lower porosity and higher mechanical performances when the parts are printed along the build plane thanks to the powerful heating ensured by the laser. In contrast, MJF samples show higher mechanical isotropy with great flexural and tensile behavior for vertically oriented parts. The role of glass beads in the material behavior is defined by their mechanical properties, meaning higher rigidity and lower strength compared to neat PA12, and fracture mechanism.</jats:p>