| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Jabbari, Masoud
University of Leeds
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (35/35 displayed)
- 2024Infusion Simulation of Graphene-Enhanced Resin in LCM for Thermal and Chemo-Rheological Analysiscitations
- 2024A Numerical Framework of Simulating Flow-Induced Deformation during Liquid Composite Mouldingcitations
- 2023A Numerical Thermo-Chemo-Flow Analysis of Thermoset Resin Impregnation in LCM Processescitations
- 2022Numerical Investigation of Multi-scale Characteristics of Single and Multi-layered Woven Structurescitations
- 2022Numerical Simulation of Two-Phase Flow in Liquid Composite Moulding Using VOF-Based Implicit Time-Stepping Schemecitations
- 2021A Numerical Analysis of Resin Flow in Woven Fabrics: Effect of Local Tow Curvature on Dual-Scale Permeabilitycitations
- 2020New magneto-rheological fluids with high stability: Experimental study and constitutive modellingcitations
- 2019The role of rheological parameters on drying behaviour of a water-based cast tapecitations
- 2019The role of rheological parameters on drying behaviour of a water-based cast tapecitations
- 2019Mechanical properties of honeycomb nanoporous siliconcitations
- 2019Mechanical properties of honeycomb nanoporous silicon: A high strength and ductile structurecitations
- 2018Multiphysics modelling of manufacturing processes: A reviewcitations
- 2018Multiphysics modelling of manufacturing processes: A reviewcitations
- 2018Multiphysics modelling of manufacturing processes: A reviewcitations
- 2017Drying of a tape-cast layer: Numerical investigation of influencing parameterscitations
- 2016Ceramic tape casting: A review of current methods and trends with emphasis on rheological behaviour and flow analysiscitations
- 2016Improvement in Surface Characterisitcs of Polymers for Subsequent Electroless Plating Using Liquid Assisted Laser Processingcitations
- 2016Numerical modelling of the flow in the resin infusion process on the REV scale: A feasibility studycitations
- 2016Rheological Characterization of Green Sand Flow
- 2016Numerical modelling of evaporation in a ceramic layer in the tape casting process
- 2016Modeling coupled heat and mass transfer during drying in tape casting with a simple ceramics–water systemcitations
- 2016Modelling of fluid flow in tape casting of thin ceramics: Analytical approaches and numerical investigationscitations
- 2016Improvement in surface characterisitcs of polymers for subsequent electroless plating using liquid assisted laser processingcitations
- 2016Particle migration using local variation of the viscosity (LVOV) model in flow of a non-Newtonian fluid for ceramic tape castingcitations
- 2015Modelling of fluid flow in tape casting of thin ceramics: analytical approaches and numerical investigations
- 2014An evaluation of interface capturing methods in a VOF based model for multiphase flow of a non-Newtonian ceramic in tape castingcitations
- 2014Bingham plastic fluid flow model in tape casting of ceramics using two doctor blades – analytical approachcitations
- 2013Modeling of the interface behavior in tape casting of functionally graded ceramics for magnetic refrigeration partscitations
- 2013Quasi-steady state power law model for flow of (La0·85Sr0·15)0·9MnO3 ceramic slurry in tape castingcitations
- 2013Numerical Modeling of the Side Flow in Tape Casting of a Non-Newtonian Fluidcitations
- 2013Interface Behavior in Functionally Graded Ceramics for the Magnetic Refrigeration: Numerical Modelingcitations
- 2013Numerical modeling of coupled heat transfer and phase transformation for solidification of the gray cast ironcitations
- 2012Numerical modeling and experimental validation of microstructure in gray cast ironcitations
- 2012Numerical modeling of the flow of a power law ceramic slurry in the tape casting process
- 2012Interface Oscillation in the Side-by-Side (SBS) Tape Casting of Functionally Graded Ceramics (FGCs)
Places of action
| Organizations | Location | People |
|---|
document
Interface Oscillation in the Side-by-Side (SBS) Tape Casting of Functionally Graded Ceramics (FGCs)
Abstract
<p>Room temperature magnetic refrigeration is a new highly efficient and environmentally protective technology. Although it has not been maturely developed, it shows great applicable prosperity and seems to be a potential substitute for the traditional vapor compression technology. Tape Casting is a common process in producing multilayer ceramics, which now is used for producing side-by-side (SBS) functionally graded ceramics (FGCs). These FGCs are mostly used in the magnetic refrigeration sectors due to the varying composition of the magnetocaloric materials so that the magnetic transition temperature of the magnetic regenerator varies along the paths. The main goal of this research is to study the multiple material flow in SBS tape casting and analyze its influence on the interface between the stripes. The materials used for the experimental part are <em>La<sub>0.85</sub>Sr<sub>0.15</sub>MnO<sub>3</sub></em> and <em>Ce<sub>0.9</sub>Gd<sub>0.1</sub>O<sub>2</sub></em>ceramic slurries. The rheological behavior of the slurries are extracted from experiments and used in the ANSYS FLUENT commercial code to develop a fluid flow model for the non-Newtonian ceramic slurries and evaluate the interface oscillation between the stripes in SBS tape casting. The Numerical results show reasonable agreement with corresponding experimental results.</p>