| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Czaja, Paweł
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2024Sb/Sb4O5Cl2/C composite as a stable anode for sodium-ion batteriescitations
- 2024Nanocomposites Based on Thermoplastic Acrylic Resin with the Addition of Chemically Modified Multi-Walled Carbon Nanotubescitations
- 2024The Influence of Er and Zr on the Microstructure and Durability of the Mechanical Properties of an Al-Mg Alloy Containing 7 wt.% of Mgcitations
- 2023The Interfacial Phenomena Between Graphene on Cu Substrate Covered by Ni, Cu, or W Layer, with Liquid Ga-Sn-Zn Alloycitations
- 2023Wetting and Interfacial Chemistry of New Pb-Free Sn-Zn-Ag-Al-Li (SZAAL) Solder with Cu, Ni, and Al Substratescitations
- 2023Phase Evolution at the Interface between Liquid Solder Sn-Zn-Ag and Cu Substrate Studied by In Situ Heating Scanning Transmission Electron Microscopycitations
- 2023Microstructural characterization of rapidly solidified Al-13.5 at.% Cr and Al-13.5 at.% V alloys for catalytic applications
- 2023Effect of High-Pressure Torsion on Phase Formation and Mechanical Properties of a High-Entropy TiZrHfMoCrCo Alloycitations
- 2021New Insights into the Intermartensitic Transformation and Over 11% Magnetic Field‐Induced Strain in 14 m Ni−Mn−Ga Martensitecitations
- 2021Microstructure and magnetic properties of selected laser melted Ni-Mn-Ga and Ni-Mn-Ga-Fe powders derived from as melt-spun ribbons precursorscitations
- 2021Suppression and Recovery of Martensitic Transformation and Magnetism in Mechanically and Thermally Treated Magnetic Shape‐Memory Ni−Mn−Ga Melt‐Spun Ribbonscitations
- 2019Microstructural anisotropy, phase composition and magnetic properties of as-cast and annealed Ni-Mn-Ga-Co-Cu melt-spun ribbonscitations
- 2019Microstructural origins of martensite stabilization in Ni49Co1Mn37.5Sn6.5In6 metamagnetic shape memory alloycitations
- 2019On the magnetic contribution to the inverse magnetocaloric effect in Ni-Co-Cu-Mn-Sn metamagnetic shape memory alloyscitations
Places of action
| Organizations | Location | People |
|---|
article
Microstructure and magnetic properties of selected laser melted Ni-Mn-Ga and Ni-Mn-Ga-Fe powders derived from as melt-spun ribbons precursors
Abstract
<p>Selective Laser Melting was successfully used as a fabrication method to produce Ni-MnGa and Ni-Mn-Ga-Fe ferromagnetic shape memory alloys. The starting material in a powder form with an average particle size of about 17.6 µm was produced by milling of as melt-spun ribbons. The microstructure, phase composition, and martensitic transformation behavior of both powder precursors and laser melted alloys were investigated by several methods, including high energy Xray diffraction, electron microscopy, and vibrating sample magnetometry. The as laser melted materials are chemically homogenous and show a typical layered microstructure. Both alloy compositions have a duplex structure consisting either of austenite and 10M martensite (Ni-Mn-Ga) or a mixture of 14M and NM martensitic phases (Ni-Mn-Ga-Fe), contrary to the as milled powder precursors showing fcc structure in both cases. The forward martensitic transformation takes place at 336 and 325 K for Ni-Mn-Ga and Ni-Mn-Ga-Fe, respectively, while the magnetic response is much stronger for Ni-Mn-Ga than for the quaternary alloy. The results show that Selective Laser Melting allows for producing of good quality, homogenous materials. However, their microstructural features and consequently shape memory behavior should be tailored by additional heat treatment.</p>