| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Zou, Zhenmin
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (18/18 displayed)
- 2025Effect of micro-scale fibre uncertainties on the mechanical behaviour of natural/synthetic hybrid fibre compositescitations
- 2024Intra-yarn fibre hybridisation effect on homogenised elastic properties and micro and meso-stress analysis of 2D woven laminae: Two-scale FE modelcitations
- 2024A two‐scale numerical analysis of intra‐yarn hybrid natural/synthetic woven composites
- 2024The static and fatigue failure of co-cured composite joints with two-scale interface tougheningcitations
- 2024Zero-tension fatigue behaviour of co-cured composite step joints with multiscale toughening
- 2024A two-scale numerical analysis of intra-yarn hybridnatural/synthetic woven composites
- 2024Fatigue Characterization of Composite Laminates with Interface Hybrid Toughening Using a Single-Step Joint Configurationcitations
- 2023Micromechanics of intra-laminar hybrid lamina with hollow fibres:
- 2023The effect of hygrothermal ageing on the delamination of Carbon/epoxy laminates with Core-shell rubber nanoparticle and Micro-fibre thermoplastic veil tougheningcitations
- 2023Micromechanics of intra-laminar hybrid lamina with hollow fibres::a RVE model
- 2022On the effect of binders on interlaminar fracture energies and R-curves of carbon/epoxy laminates with non-woven micro-fibre veilscitations
- 2022On the effect of binders on interlaminar fracture energies and R-curves of carbon/epoxy laminates with non-woven micro-fibre veilscitations
- 2022On the R-curve behaviour of carbon/epoxy laminates with core-shell rubber nanoparticle and micro-fibre veil hybrid toughening: Carbon vs PPS veilscitations
- 2022Thermally induced residual micro-stresses in hybrid composite laminates with tow-level fibre hybridization
- 2022Thermally induced residual micro-stresses in hybrid composite laminates with tow-level fibre hybridization
- 2018A computationally efficient cohesive zone model for fatiguecitations
- 2017Frequency-Dependent Cohesive Zone Models for Fatiguecitations
- 2008Analysis of crack propagation in nuclear graphite using three-point bending of sandwiched specimenscitations
Places of action
| Organizations | Location | People |
|---|
article
A computationally efficient cohesive zone model for fatigue
Abstract
cohesive zone model has been developed for the simulation of both high and low cycle fatigue crack growth. The developed model provides an alternative approach that reflects the computational efficiency of the well-established envelop-load damage model yet can deliver the accuracy of the equally well-established loading-unloading hysteresis damage model. A feature included in the new cohesive zone model is a damage mechanism that accumulates as a result of cyclic plastic separation and material deterioration to capture a finite fatigue life. The accumulation of damage is reflected in the loading-unloading hysteresis curve, but additionally, the model incorporates a fast-track feature. This is achieved by ?freezing in? a particular damage state for one loading cycle over a predefined number of cycles. The new model is used to simulate mode I fatigue crack growth in austenitic stainless steel 304 at significant reduction in the computational cost.