| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Unluer, Cise
University of Glasgow
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2023Strain hardening magnesium-silicate-hydrate composites with extremely low fiber dosage of 0.5% by volumecitations
- 2023MgO‐based cements – Current status and opportunitiescitations
- 2022Potential additives for magnesia-based concrete with enhanced performance and propensity for CO2 sequestrationcitations
- 2022New frontiers in sustainable cementscitations
- 2022Potential additives for magnesia-based concrete with enhanced performance and propensity for CO 2 sequestrationcitations
- 2021Improving the carbonation resistance of Na2CO3-activated slag mixes via the use of reactive MgO and nucleation seedingcitations
- 2021Mechanical and microstructural changes in reactive magnesium oxide cement-based concrete mixes subjected to high temperaturescitations
- 2021Thermal and mechanical performance of a novel 3D printed macro-encapsulation method for phase change materialscitations
- 2020Performance of reactive magnesia cement formulations containing fly ash and ground granulated blast-furnace slagcitations
- 2020Mechanical properties and flexural behavior of sustainable bamboo fiber-reinforced mortarcitations
- 2018Improving the Carbonation of Reactive MgO Cement Concrete via the Use of NaHCO3 and NaClcitations
- 2018Improving the Carbonation of Reactive MgO Cement Concrete via the Use of NaHCO 3 and NaClcitations
- 2018Development of MgO concrete with enhanced hydration and carbonation mechanismscitations
- 2017Performance and microstructural development of MgO-SiO 2 binders under different curing conditionscitations
- 2017Influence of nucleation seeding on the performance of carbonated MgO formulationscitations
- 2017Performance and microstructural development of MgO-SiO2 binders under different curing conditionscitations
Places of action
| Organizations | Location | People |
|---|
article
Thermal and mechanical performance of a novel 3D printed macro-encapsulation method for phase change materials
Abstract
The mechanical and thermal properties of a novel 3D-printed macro-encapsulation method for Phase Change Materials (PCMs) was investigated and compared to mixtures that contain commercially available micro-encapsulated PCMs. Two types of cement-based mixtures, a mortar mix with a density of 2,161 kg/m3 and a lightweight mix with a density of 1,351 kg/m3, were utilized for both the micro- and macro-encapsulated samples. The micro-encapsulated mortar and lightweight samples contain 0 vol%, 10 vol%, and 20 vol% of PCMs with a melting point of 28 °C. The macro-encapsulated samples contain 20 vol% of the same PCMs but in this case the PCMs were incorporated into a hollow 3D-printed polymer lattice which is embedded in the cement-based matrices. This lattice not only serves as macro-encapsulation but also as reinforcement to enhance the ductility of cement-based materials. The results reviled that the lattice specimens developed the lowest panel temperature during heating and showed a significant reduction of the indoor temperature. The mechanical properties of the lattice specimens were improved and resulted in a change from a brittle to strain-hardening behavior. This research shows the potential of the developed system to be uses for thermal retrofitting or as wall elements to lower the indoor temperature and save energy in tropical climates.