| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Lancaster, Mj
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (24/24 displayed)
- 2022D-band waveguide diplexer fabricated using micro laser sinteringcitations
- 2022Compact monolithic SLM 3D-printed filters using pole-generating resonant irisescitations
- 20213D printed re-entrant cavity resonator for complex permittivity measurement of crude oilscitations
- 2021Two‐GHz hybrid coaxial bandpass filter fabricated by stereolithography 3‐D printing
- 20213D printed coaxial microwave resonator sensor for dielectric measurements of liquidcitations
- 2020180 GHz Waveguide Bandpass Filter Fabricated by 3D Printing Technologycitations
- 201990 GHz Micro Laser Sintered Filter: Reproducibility and Quality Assessmentcitations
- 2018W-Band Waveguide Bandpass Filters Fabricated by Micro Laser Sinteringcitations
- 2018Microwave filters based on novel dielectric split-ring resonators with high unloaded quality factorscitations
- 2016Permittivity and loss characteristics of SU8-quartz composite photoresist at THz frequenciescitations
- 2016W-Band waveguide filters fabricated by laser micromachining and 3-D printingcitations
- 2014Uncertainties in the permittivity of thin films extracted from measurements with near field microwave microscopy calibrated by an image charge modelcitations
- 2009Two-dimensional growth of SrTiO3 thin films on (001) MgO substrates using pulsed laser deposition and reflection high energy electron diffractioncitations
- 2009Comparison of scanning evanescent microwave microscopy with co-planar waveguide methods of characterization of BaSr TiO thin films
- 2009Comparison of structural, microstructural, and electrical analyses of barium strontium titanate thin filmscitations
- 2008BaxSr1 - xTiO3 Thin Films for Tunable Microwave Devices in Cryogenic and Room Temperature Applicationcitations
- 2007Fabrication and characterisation of barium strontium titante thick film device structures for microwave applicationscitations
- 2007Optical properties of barium strontium titanate (BST) ferroelectric thin filmscitations
- 2007Fabrication and Characterisation of Barium Strontium Titanate Thick Film Device Structures for Microwave Applicationscitations
- 2006Temperature Dependent Dielectric Properties of Coplanar Phase Shifters Fabricated from Ba₀.₅SR₀.₅Ti0₃ Thin Filmscitations
- 2006Microwave and Microstructural Properties of Ba₀.₅Sr₀.₅TiO₃ of Thin Film Coplanar Phase Shifterscitations
- 2004High frequency thick film BST ferroeclectric phase shiftercitations
- 2004Growth, Microwave Properties and Microstructure of Ba₀₊₀₅Sr₀₊₉₅TiO₃ Thin Filmscitations
- 2003A High Temperature Superconducting Butler Matrixcitations
Places of action
| Organizations | Location | People |
|---|
article
Two‐GHz hybrid coaxial bandpass filter fabricated by stereolithography 3‐D printing
Abstract
This brief presents a fourth‐order hybrid coaxial bandpass filter, which is fabricated using Stereolithography 3‐D printing. The filter is designed to operate at a center frequency of 2 GHz, with a bandwidth of 40 MHz, a Chebyshev response and two symmetrical transmission zeros at 1.96 GHz and 2.04 GHz to achieve a better frequency selectivity. Usually in coaxial cavity filter design, the main‐line couplings and cross couplings are realized using coupling irises or probes. However, in the filter presented here, the main‐line couplings between coaxial resonators and input/output coupling are realized using Printed Circuit Board (PCB) lines instead. This novel idea allows different topologies to be designed easily by altering the PCB layout. It also allows multiple cross couplings to be included in the PCB layout for different filter topologies. In addition, the quality factor of each of the coaxial resonators in the filter is increased by introducing base rounding in the resonator. The filter was tested, and the measurement result of the filter shows very good agreement with simulated result without tuning, which indicates the accuracy of the fabrication process.